ich habe auf meinem Notebook Ubuntu 5.04 installiert, vorher hatte ich Sarge drauf.
Bei beiden Installationen hatte ich das Problem, das ich den DMA Modus meiner Platte nur auf 2 stellen konnte, die Info-Ausgabe sagt aber das 5 (logischerweise
) möglich ist.hdparm -i output:
Code: Alles auswählen
/dev/hda:
Model=IC25N030ATMR04-0, FwRev=MOAOAD4A, SerialNo=MRG218K2D0YR1J
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=1740kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=58605120
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:
* signifies the current active mode
Code: Alles auswählen
/dev/hda:
ATA device, with non-removable media
Model Number: IC25N030ATMR04-0
Serial Number: MRG218K2D0YR1J
Firmware Revision: MOAOAD4A
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 3a
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 16 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 58605120
LBA48 user addressable sectors: 58605120
device size with M = 1024*1024: 28615 MBytes
device size with M = 1000*1000: 30005 MBytes (30 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Vendor, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: 128 (0x80)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
Address Offset Reserved Area Boot
* SET FEATURES subcommand required to spinup after power up
Power-Up In Standby feature set
* Advanced Power Management feature set
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
26min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
