das ist mein erster Post hier. Beim Booten meiner Debian 8.0 jessie Maschine muss ich relativ lange warten.
Folgendes sagt "dmesg"
Code: Alles auswählen
...
[ 1.159069] pnp: PnP ACPI: found 12 devices
[ 1.159070] ACPI: ACPI bus type pnp unregistered
[ 1.165536] pci 0000:01:00.0: no compatible bridge window for [mem 0xfff80000-0xffffffff pref]
[ 1.165540] pci 0000:03:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[ 1.165544] PCI: max bus depth: 1 pci_try_num: 2
[ 1.165570] pci 0000:00:1c.1: BAR 15: assigned [mem 0xbfb00000-0xbfbfffff pref]
[ 1.165573] pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x80000)
[ 1.165576] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 1.165578] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
[ 1.165582] pci 0000:00:01.0: bridge window [mem 0xd2000000-0xd2ffffff]
[ 1.165585] pci 0000:00:01.0: bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 1.165589] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 1.165592] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 1.165598] pci 0000:00:1c.0: bridge window [mem 0xd3500000-0xd35fffff]
[ 1.165608] pci 0000:03:00.0: BAR 6: assigned [mem 0xbfb00000-0xbfb0ffff pref]
[ 1.165611] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 1.165616] pci 0000:00:1c.1: bridge window [mem 0xd3400000-0xd34fffff]
[ 1.165621] pci 0000:00:1c.1: bridge window [mem 0xbfb00000-0xbfbfffff pref]
[ 1.165640] pci 0000:00:01.0: setting latency timer to 64
[ 1.165653] pci 0000:00:1c.0: setting latency timer to 64
[ 1.165665] pci 0000:00:1c.1: setting latency timer to 64
[ 1.165669] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.165671] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.165673] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.165676] pci_bus 0000:00: resource 7 [mem 0xbfa00000-0xfeafffff]
[ 1.165678] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 1.165680] pci_bus 0000:01: resource 1 [mem 0xd2000000-0xd2ffffff]
[ 1.165682] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 1.165684] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 1.165686] pci_bus 0000:02: resource 1 [mem 0xd3500000-0xd35fffff]
[ 1.165689] pci_bus 0000:03: resource 1 [mem 0xd3400000-0xd34fffff]
[ 1.165691] pci_bus 0000:03: resource 2 [mem 0xbfb00000-0xbfbfffff pref]
[ 1.165785] NET: Registered protocol family 2
[ 1.167719] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 1.168549] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 1.169723] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.169859] TCP: Hash tables configured (established 524288 bind 65536)
[ 1.169861] TCP reno registered
[ 1.169874] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 1.169905] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 1.170037] NET: Registered protocol family 1
[ 1.170051] pci 0000:00:02.0: Boot video device
[ 2.767980] pci 0000:00:1a.0: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 4.365602] pci 0000:00:1d.0: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 4.365770] PCI: CLS 64 bytes, default 64
[ 4.365811] Unpacking initramfs...
[ 4.596172] Freeing initrd memory: 10664k freed
[ 4.597433] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 4.597436] Placing 64MB software IO TLB between ffff8800b6ab9000 - ffff8800baab9000
[ 4.597439] software IO TLB at phys 0xb6ab9000 - 0xbaab9000
[ 4.597456] Simple Boot Flag at 0x44 set to 0x1
[ 4.598128] audit: initializing netlink socket (disabled)
[ 4.598137] type=2000 audit(1424977881.372:1): initialized
[ 4.613642] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 4.614457] VFS: Disk quotas dquot_6.5.2
[ 4.614491] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 4.614562] msgmni has been set to 15750
[ 4.614722] alg: No test for stdrng (krng)
[ 4.614755] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 4.614758] io scheduler noop registered
[ 4.614760] io scheduler deadline registered
[ 4.614790] io scheduler cfq registered (default)
[ 4.614861] pcieport 0000:00:01.0: setting latency timer to 64
[ 4.614887] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 4.615042] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 4.615060] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 4.615062] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 4.615398] intel_idle: MWAIT substates: 0x21120
[ 4.615400] intel_idle: v0.4 model 0x3A
[ 4.615401] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 4.615439] ERST: Table is not found!
[ 4.615440] GHES: HEST is not enabled!
[ 4.615485] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 4.821347] Linux agpgart interface v0.103
[ 4.821425] agpgart-intel 0000:00:00.0: Intel Ivybridge Chipset
[ 4.821489] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 4.822789] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[ 4.822913] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 4.823039] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS5] at 0x60,0x64 irq 1,12
[ 4.835144] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.835150] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.835270] mousedev: PS/2 mouse device common for all mice
[ 4.836938] rtc_cmos 00:06: RTC can wake from S4
[ 4.837050] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 4.837079] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 4.837234] cpuidle: using governor ladder
[ 4.837426] cpuidle: using governor menu
[ 4.837595] TCP cubic registered
[ 4.837812] NET: Registered protocol family 10
[ 4.838357] Mobile IPv6
[ 4.838359] NET: Registered protocol family 17
[ 4.838363] Registering the dns_resolver key type
[ 4.838493] PM: Hibernation image not present or could not be loaded.
[ 4.838504] registered taskstats version 1
[ 4.839182] rtc_cmos 00:06: setting system clock to 2015-02-26 19:11:21 UTC (1424977881)
[ 4.839254] Initializing network drop monitor service
[ 4.840314] Freeing unused kernel memory: 576k freed
[ 4.840376] Write protecting the kernel read-only data: 6144k
[ 4.842729] Freeing unused kernel memory: 644k freed
[ 4.845114] Freeing unused kernel memory: 688k freed
[ 4.852635] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 4.856043] systemd-udevd[81]: starting version 215
[ 4.869695] thermal LNXTHERM:00: registered as thermal_zone0
[ 4.869699] ACPI: Thermal Zone [TZ00] (52 C)
[ 4.870858] usbcore: registered new interface driver usbfs
[ 4.870876] usbcore: registered new interface driver hub
[ 4.870938] usbcore: registered new device driver usb
[ 4.871143] SCSI subsystem initialized
[ 4.871349] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.871394] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 4.871398] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 4.871419] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 4.871445] ehci_hcd 0000:00:1a.0: debug port 2
[ 4.873287] libata version 3.00 loaded.
[ 4.875340] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 4.875358] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xd3619000
[ 4.888908] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 4.888942] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.888944] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.888947] usb usb1: Product: EHCI Host Controller
[ 4.888948] usb usb1: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[ 4.888950] usb usb1: SerialNumber: 0000:00:1a.0
[ 4.889152] hub 1-0:1.0: USB hub found
[ 4.889157] hub 1-0:1.0: 2 ports detected
[ 4.889276] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.889281] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 4.889289] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 4.889317] ehci_hcd 0000:00:1d.0: debug port 2
[ 4.893196] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 4.893215] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xd3618000
[ 4.908864] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 4.908898] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.908900] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.908903] usb usb2: Product: EHCI Host Controller
[ 4.908904] usb usb2: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[ 4.908906] usb usb2: SerialNumber: 0000:00:1d.0
[ 4.909101] hub 2-0:1.0: USB hub found
[ 4.909107] hub 2-0:1.0: 2 ports detected
[ 4.909192] ahci 0000:00:1f.2: version 3.0
[ 4.909313] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 4.909360] ahci: SSS flag set, parallel bus scan disabled
[ 4.924864] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode
[ 4.924869] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems apst
[ 4.924876] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.933799] scsi0 : ahci
[ 4.934082] scsi1 : ahci
[ 4.934257] scsi2 : ahci
[ 4.934421] scsi3 : ahci
[ 4.934583] scsi4 : ahci
[ 4.934726] scsi5 : ahci
[ 4.934792] ata1: SATA max UDMA/133 abar m2048@0xd3617000 port 0xd3617100 irq 41
[ 4.934796] ata2: DUMMY
[ 4.934801] ata3: SATA max UDMA/133 abar m2048@0xd3617000 port 0xd3617200 irq 41
[ 4.934804] ata4: DUMMY
[ 4.934805] ata5: DUMMY
[ 4.934806] ata6: DUMMY
[ 4.934918] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 4.934924] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 4.934936] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 4.935035] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 4.935084] xhci_hcd 0000:00:14.0: irq 42 for MSI/MSI-X
[ 4.935141] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.935143] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.935145] usb usb3: Product: xHCI Host Controller
[ 4.935147] usb usb3: Manufacturer: Linux 3.2.0-4-amd64 xhci_hcd
[ 4.935149] usb usb3: SerialNumber: 0000:00:14.0
[ 4.935236] xHCI xhci_add_endpoint called for root hub
[ 4.935239] xHCI xhci_check_bandwidth called for root hub
[ 4.935268] hub 3-0:1.0: USB hub found
[ 4.935276] hub 3-0:1.0: 4 ports detected
[ 4.935339] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 4.935344] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 4.935361] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 4.935363] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.935365] usb usb4: Product: xHCI Host Controller
[ 4.935367] usb usb4: Manufacturer: Linux 3.2.0-4-amd64 xhci_hcd
[ 4.935369] usb usb4: SerialNumber: 0000:00:14.0
[ 4.935439] xHCI xhci_add_endpoint called for root hub
[ 4.935441] xHCI xhci_check_bandwidth called for root hub
[ 4.935469] hub 4-0:1.0: USB hub found
[ 4.935477] hub 4-0:1.0: 4 ports detected
[ 5.200439] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 5.252365] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 5.254336] ata1.00: supports DRM functions and may not be fully accessible
[ 5.254360] ata1.00: ATA-9: Samsung SSD 840 EVO 250GB, EXT0BB6Q, max UDMA/133
[ 5.254363] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 5.254622] ata1.00: supports DRM functions and may not be fully accessible
[ 5.254649] ata1.00: configured for UDMA/133
[ 5.254871] scsi 0:0:0:0: Direct-Access ATA Samsung SSD 840 EXT0 PQ: 0 ANSI: 5
[ 5.332646] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 5.332650] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.333050] hub 1-1:1.0: USB hub found
[ 5.333104] hub 1-1:1.0: 6 ports detected
[ 5.444082] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[ 5.571882] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.573729] ata3.00: ATAPI: HL-DT-ST DVDRAM GU70N, DE01, max UDMA/133
[ 5.575710] ata3.00: configured for UDMA/133
[ 5.576397] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 5.576402] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.576663] scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GU70N DE01 PQ: 0 ANSI: 5
[ 5.576690] hub 2-1:1.0: USB hub found
[ 5.576748] hub 2-1:1.0: 6 ports detected
[ 5.580216] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 5.580348] sd 0:0:0:0: [sda] Write Protect is off
[ 5.580352] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.580381] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.582045] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.582058] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 5.582156] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 5.582920] sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
[ 5.583405] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.584046] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.584089] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 5.595811] Refined TSC clocksource calibration: 2095.242 MHz.
[ 5.595815] Switching to clocksource tsc
[ 5.743626] usb 3-4: new high-speed USB device number 2 using xhci_hcd
[ 5.767976] usb 3-4: New USB device found, idVendor=04f2, idProduct=b3bd
[ 5.767980] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.767983] usb 3-4: Product: Lenovo EasyCamera
[ 5.767984] usb 3-4: Manufacturer: Vimicro corp.
[ 5.839650] usb 1-1.2: new full-speed USB device number 3 using ehci_hcd
[ 5.934986] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c52b
[ 5.934990] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.934992] usb 1-1.2: Product: USB Receiver
[ 5.934994] usb 1-1.2: Manufacturer: Logitech
[ 5.937967] usbcore: registered new interface driver usbhid
[ 5.937969] usbhid: USB HID core driver
[ 5.941034] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1a.0-1.2/input2
[ 5.944149] input: Logitech Unifying Device. Wireless PID:1017 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.2/0003:046D:C52B.0003/input/input1
[ 5.944314] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1017] on usb-0000:00:1a.0-1.2:1
[ 6.007405] usb 1-1.3: new full-speed USB device number 4 using ehci_hcd
[ 6.101509] usb 1-1.3: New USB device found, idVendor=0cf3, idProduct=3004
[ 6.101513] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.101515] usb 1-1.3: Product: Bluetooth USB Host Controller
[ 6.101517] usb 1-1.3: Manufacturer: Atheros Communications
[ 6.101519] usb 1-1.3: SerialNumber: Alaska Day 2006
[ 6.171150] usb 1-1.4: new high-speed USB device number 5 using ehci_hcd
[ 6.263761] usb 1-1.4: New USB device found, idVendor=0bda, idProduct=0129
[ 6.263765] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.263768] usb 1-1.4: Product: USB2.0-CRW
[ 6.263769] usb 1-1.4: Manufacturer: Generic
[ 6.263771] usb 1-1.4: SerialNumber: 20100201396000000
[ 6.378220] PM: Starting manual resume from disk
[ 6.378224] PM: Hibernation image partition 8:6 present
[ 6.378226] PM: Looking for hibernation image.
[ 6.378434] PM: Image not found (code -22)
[ 6.378436] PM: Hibernation image not present or could not be loaded.
[ 6.387260] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 6.693600] systemd[1]: RTC configured in localtime, applying delta of 60 minutes to system time.
[ 9.898497] lp: driver loaded but no devices found
[ 9.899968] ppdev: user-space parallel port driver
[ 9.902577] fuse init (API version 7.17)
[ 9.904154] loop: module loaded
[ 12.475149] systemd-udevd[204]: starting version 215
[ 12.512912] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input2
[ 12.512919] ACPI: Power Button [PWRB]
[ 12.512988] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[ 12.513024] ACPI: Lid Switch [LID0]
[ 12.513065] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 12.513069] ACPI: Power Button [PWRF]
[ 12.513410] ACPI: Requesting acpi_cpufreq
[ 12.520059] ACPI: AC Adapter [ACAD] (on-line)
[ 12.530367] ACPI: resource 0000:00:1f.3 [io 0x4040-0x405f] conflicts with ACPI region SMBI [io 0x4040-0x404f]
[ 12.530370] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.530474] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.530649] iTCO_vendor_support: vendor-support=0
[ 12.538455] Bluetooth: Core ver 2.16
[ 12.538468] NET: Registered protocol family 31
[ 12.538470] Bluetooth: HCI device and connection manager initialized
[ 12.538473] Bluetooth: HCI socket layer initialized
[ 12.538475] Bluetooth: L2CAP socket layer initialized
[ 12.538481] Bluetooth: SCO socket layer initialized
[ 12.538917] Linux media interface: v0.10
[ 12.541716] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 12.541755] usbcore: registered new interface driver btusb
[ 12.564675] cfg80211: Calling CRDA to update world regulatory domain
[ 12.589501] ACPI: Battery Slot [BAT1] (battery present)
[ 12.590586] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 12.590672] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
[ 12.590734] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 12.594257] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 12.594533] input: Ideapad extra buttons as /devices/platform/ideapad/input/input5
[ 12.594843] Bluetooth: Atheros AR30xx firmware driver ver 1.0
[ 12.595108] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 12.601108] Linux video capture interface: v2.00
[ 12.601207] [drm] Initialized drm 1.1.0 20060810
[ 12.602904] nvidia: module license 'NVIDIA' taints kernel.
[ 12.602907] Disabling lock debugging due to kernel taint
[ 12.603035] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (04f2:b3bd)
[ 12.605876] input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/input/input7
[ 12.605975] usbcore: registered new interface driver uvcvideo
[ 12.605978] USB Video Class driver (1.1.1)
[ 12.606375] i915 0000:00:02.0: setting latency timer to 64
[ 12.606871] ath9k 0000:03:00.0: setting latency timer to 64
[ 12.615376] ath: EEPROM regdomain: 0x65
[ 12.615378] ath: EEPROM indicates we should expect a direct regpair map
[ 12.615380] ath: Country alpha2 being used: 00
[ 12.615382] ath: Regpair used: 0x65
[ 12.617886] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.618197] Registered led device: ath9k-phy0
[ 12.618203] ieee80211 phy0: Atheros AR9485 Rev:1 mem=0xffffc90006f00000, irq=17
[ 12.718215] usb 1-1.3: firmware: agent aborted loading ar3k/AthrBT_0x01020200.dfu (not found?)
[ 12.718406] Bluetooth: Loading patch file failed
[ 12.718462] ath3k: probe of 1-1.3:1.0 failed with error -2
[ 12.718491] usbcore: registered new interface driver ath3k
[ 12.718515] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[ 12.718523] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 12.718525] [drm] Driver supports precise vblank timestamp query.
[ 12.718593] [drm:intel_dsm_platform_mux_info] *ERROR* MUX INFO call failed
[ 12.718977] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 12.720134] nvidia 0000:01:00.0: setting latency timer to 64
[ 12.720233] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.125 Mon Dec 1 19:58:28 PST 2014
[ 12.723567] cfg80211: World regulatory domain updated:
[ 12.723569] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.723571] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 12.723573] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 12.723575] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 12.723576] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.723578] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.723580] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[ 12.723581] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.723583] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 13.123200] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 13.315785] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f03)
[ 13.362016] fbcon: inteldrmfb (fb0) is primary device
[ 13.374324] psmouse serio1: elantech: Synaptics capabilities query result 0x78, 0x17, 0x0b.
[ 13.524627] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input8
[ 13.550228] rts5139: module is from the staging directory, the quality is unknown, you have been warned.
[ 13.551577] Initializing rts5139 USB card reader driver...
[ 13.554772] scsi6 : SCSI emulation for RTS5139 USB card reader
[ 13.555140] usbcore: registered new interface driver rts5139
[ 13.555145] Realtek rts5139 USB card reader support registered.
[ 13.555173] scsi 6:0:0:0: Direct-Access Generic- xD/SD/M.S. 1.00 PQ: 0 ANSI: 0 CCS
[ 13.556344] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 13.557810] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 13.572051] Console: switching to colour frame buffer device 170x48
[ 13.575297] fb0: inteldrmfb frame buffer device
[ 13.575298] drm: registered panic notifier
[ 13.575447] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[ 13.609528] acpi device:36: registered as cooling_device8
[ 13.609823] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:34/LNXVIDEO:00/input/input9
[ 13.609919] ACPI: Video Device [PEGP] (multi-head: yes rom: yes post: no)
[ 13.639743] acpi device:42: registered as cooling_device9
[ 13.640166] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input10
[ 13.640366] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 13.640405] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 13.640682] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[ 13.640756] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 13.828473] Adding 2635772k swap on /dev/sda6. Priority:-1 extents:1 across:2635772k SS
[ 14.182024] hda_codec: CX20757: BIOS auto-probing.
[ 14.182657] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input11
[ 14.187140] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 14.187352] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 14.196939] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
[ 20.251638] systemd-journald[180]: Received request to flush runtime journal from PID 1
[ 34.154370] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 35.961576] wlan0: authenticate with c0:25:06:22:32:2c (try 1)
[ 35.964830] wlan0: authenticated
[ 35.982206] wlan0: associate with c0:25:06:22:32:2c (try 1)
[ 35.991958] wlan0: RX AssocResp from c0:25:06:22:32:2c (capab=0x431 status=0 aid=4)
[ 35.991965] wlan0: associated
[ 35.998109] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 35.998186] cfg80211: Calling CRDA for country: DE
[ 36.004034] cfg80211: Regulatory domain changed to country: DE
[ 36.004041] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 36.004046] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 36.004050] cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 36.004054] cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 36.004058] cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2698 mBm)
[ 36.004062] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
Code: Alles auswählen
[ 14.187352] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 14.196939] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
[ 20.251638] systemd-journald[180]: Received request to flush runtime journal from PID 1
[ 34.154370] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 35.961576] wlan0: authenticate with c0:25:06:22:32:2c (try 1)
[ 35.964830] wlan0: authenticated
Schonmal danke im Vorraus.