Das hat was mit alsa zu tun. Hast du den Kernel selbstkomoiliert ?Pedde hat geschrieben:Hallo,
jetzt habe ich also die moduel-init-tools nochmal installiert und jetzt kommt folgende Meldung:
depmod: snd_mpu401_uart_new
make[2]: *** [_modinst_post] Error 1
make[2]: Leaving directory '/usr/src/linux-2.6.10'
make[1]: *** [real_stamp_image] Error 2
make[1]: Leaving directory '/usr/src/linux-2.6.10'
Was sagt mir das überhaupt und was kann ich machen, dass ich endlich mal zu einem neuen Kernel komme
Pedde
MA111 und WLAN-ng-0.2.1pre23
-
KBDCALLS
- Moderator
- Beiträge: 22447
- Registriert: 24.12.2003 21:26:55
- Lizenz eigener Beiträge: MIT Lizenz
- Wohnort: Dortmund
-
Kontaktdaten:
Was haben Windows und ein Uboot gemeinsam?
Kaum macht man ein Fenster auf, gehen die Probleme los.
EDV ist die Abkürzung für: Ende der Vernunft
Bevor du einen Beitrag postest:
Kaum macht man ein Fenster auf, gehen die Probleme los.
EDV ist die Abkürzung für: Ende der Vernunft
Bevor du einen Beitrag postest:
- Kennst du unsere Verhaltensregeln
- Lange Codezeilen/Logs gehören nach NoPaste, in Deinen Beitrag dann der passende Link dazu.
So,
ich habe mir jetzt Sarge installiert und mir auch noch den Kernel selber gebaut.
Ging alles einwandfrei, auch die Installation von wlan-ng
aber bei folgendenden Befehelen hänge ich fest:
modprobe prism2_usb prism2_doreset=1
prism2_usb: no version for "p80211netdev_rx found: kernel tainted
...
danach kommt dann laut Anleitung ein
wlanctl-ng wlan0 lnxreq_ifstate ifstate=enable
wlanctl-ng: No such device
--
Was mache ich verkehrt oder wie bekomme ich nun meinen Netzzugang?
Bitte um Hilfe Pedde
ich habe mir jetzt Sarge installiert und mir auch noch den Kernel selber gebaut.
Ging alles einwandfrei, auch die Installation von wlan-ng
aber bei folgendenden Befehelen hänge ich fest:
modprobe prism2_usb prism2_doreset=1
prism2_usb: no version for "p80211netdev_rx found: kernel tainted
...
danach kommt dann laut Anleitung ein
wlanctl-ng wlan0 lnxreq_ifstate ifstate=enable
wlanctl-ng: No such device
--
Was mache ich verkehrt oder wie bekomme ich nun meinen Netzzugang?
Bitte um Hilfe Pedde
jetzt habe ich mal noch einen anderen thread hier gelesen und da wurde eine Ausgabe von iwconfig benötigt, die sieht bei mir so aus:
Kann mir keiner mehr weiter helfen?
Code: Alles auswählen
iwconfig
lo no wireless extensions
eth0 no wireless extensionsMahlzeit,
ich habe jetzt auch mal andere Versionen von wlan-ng ausprobiert (0.2.0 und 0.2.1-pre26) und auch ne andere Version von hotplug (hotplug-2004_03_29)
leider brachte das alles nicht den gewünschten Erfolg.
In der Hoffnung, daß Ihr mir weiter helfen könnt poste ich mal die Outputs von lsmod und dmesg:
Ich bin so langsam am verzweifeln, weil ich das nicht hinbekomme
Danke schonmal für Eure Hilfe
Pedde
ich habe jetzt auch mal andere Versionen von wlan-ng ausprobiert (0.2.0 und 0.2.1-pre26) und auch ne andere Version von hotplug (hotplug-2004_03_29)
leider brachte das alles nicht den gewünschten Erfolg.
In der Hoffnung, daß Ihr mir weiter helfen könnt poste ich mal die Outputs von lsmod und dmesg:
Code: Alles auswählen
lsmod:
Module Size Used by
apm 19948 1
fm801_gp 3840 0
gameport 4736 1 fm801_gp
bt878 11188 0
via_agp 8832 1
parport_pc 33348 0
tsdev 7168 0
parport 37320 1 parport_pc
mousedev 9996 0
floppy 54992 0
psmouse 17800 0
pcspkr 3816 0
rtc 12088 0
evdev 9088 0
agpgart 31784 1 via_agp
uhci_hcd 29328 0
tuner 18320 0
tvaudio 20748 0
bttv 143052 1 bt878
video_buf 20356 1 bttv
i2c_algo_bit 8968 1 bttv
v4l2_common 6400 1 bttv
btcx_risc 4744 1 bttv
i2c_core 22416 4 tuner,tvaudio,bttv,i2c_algo_bit
snd_bt87x 13640 0
snd_fm801 18376 0
snd_pcm 85384 2 snd_bt87x,snd_fm801
snd_page_alloc 11144 2 snd_bt87x,snd_pcm
snd_tea575x_tuner 4096 1 snd_fm801
videodev 9856 2 bttv,snd_tea575x_tuner
snd_ac97_codec 59268 1 snd_fm801
snd_opl3_lib 9728 1 snd_fm801
snd_timer 23172 2 snd_pcm,snd_opl3_lib
snd_hwdep 9092 1 snd_opl3_lib
snd_mpu401_uart 7296 1 snd_fm801
snd_rawmidi 23204 1 snd_mpu401_uart
snd_seq_device 7944 2 snd_opl3_lib,snd_rawmidi
snd 50660 10 snd_bt87x,snd_fm801,snd_pcm,snd_ac97_codec,snd_opl3_lib,snd_timer,snd_hwdep,snd_mpu401_uart,snd_rawm
idi,snd_seq_device
soundcore 9824 2 bttv,snd
3c59x 36776 0
prism2_usb 69892 0
usbcore 104164 4 uhci_hcd,prism2_usb
p80211 30736 1 prism2_usb
prism54 47388 0
firmware_class 9728 1 prism54
ide_cd 38176 0
cdrom 35740 1 ide_cd
isofs 33976 0
ext3 109672 6
jbd 54552 1 ext3
ide_generic 1664 0
via82cxxx 12956 1
ide_disk 16768 9
ide_core 125028 4 ide_cd,ide_generic,via82cxxx,ide_disk
unix 26036 12
Code: Alles auswählen
dmesg:
Linux version 2.6.8 (root@linuxpc) (gcc-Version 3.3.4 (Debian 1:3.3.4-13)) #1 Fri Feb 25 12:40:55 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001c000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
448MB LOWMEM available.
On node 0 totalpages: 114688
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 110592 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI disabled because your bios is from 2000 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 534.539 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 447352k/458752k available (1210k kernel code, 10652k reserved, 682k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1048.57 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
CPU: Intel Pentium III (Katmai) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 534.0466 MHz.
..... host bus clock speed is 133.0616 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4304k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb150, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbd80
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbda8, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0596] at 0000:00:07.0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4304 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 196k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596b (rev 22) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 31536U2, ATA DISK drive
hdb: FUJITSU MPG3409AH EF, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 30015216 sectors (15367 MB) w/512KiB Cache, CHS=29777/16/63, UDMA(66)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
hdb: max request size: 128KiB
hdb: 80063424 sectors (40992 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(66)
/dev/ide/host0/bus0/target1/lun0: p1
hdc: CD-RW IDE5224, ATAPI CD/DVD-ROM drive
hdd: CRD-8482B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 840632k swap on /dev/hda7. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
Loaded prism54 driver, version 1.2
usbcore: registered new driver usbfs
usbcore: registered new driver hub
prism2_usb: no version for "p80211netdev_rx" found: kernel tainted.
prism2usb_init: prism2_usb.o: 0.2.1-pre23 Loaded
prism2usb_init: dev_info is: prism2_usb
usbcore: registered new driver prism2_usb
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
PCI: Found IRQ 9 for device 0000:00:0c.0
3c59x: Donald Becker and others. [url]www.scyld.com/network/vortex.html[/url]
0000:00:0c.0: 3Com PCI 3c905C Tornado at 0xe000. Vers LK1.1.19
Linux video capture interface: v1.00
PCI: Found IRQ 9 for device 0000:00:0b.0
PCI: Found IRQ 5 for device 0000:00:0a.1
PCI: Sharing IRQ 5 with 0000:00:0a.0
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
PCI: Found IRQ 5 for device 0000:00:0a.0
PCI: Sharing IRQ 5 with 0000:00:0a.1
bttv0: Bt878 (rev 2) at 0000:00:0a.0, irq: 5, latency: 64, mmio: 0xeb002000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00fffffb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom: model=61204, tuner=Philips FI1216 MK2 (5), radio=no
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951),ta8874z
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 10, io base 0000d400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using address 2
usb 1-2: new full speed USB device using address 3
Linux agpgart interface v0.100 (c) Dave Jones
Real Time Clock Driver v1.12
input: PC Speaker
input: GenPS/2 Genius Wheel Mouse on isa0060/serio1
inserting floppy driver for 2.6.8
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: Maximum main memory to use for agp memory: 381M
agpgart: AGP aperture is 64M @ 0xe0000000
bt878: AUDIO driver version 0.0.0 loaded
gameport: at pci0000:00:0b.1 speed 1807 kHz
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02a4a60(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
usb 1-2: USB disconnect, address 3
usb 1-2: new full speed USB device using address 4
Danke schonmal für Eure Hilfe
Pedde
Mahlzeit,
ich habe jetzt auch mal andere Versionen von wlan-ng ausprobiert (0.2.0 und 0.2.1-pre26) und auch ne andere Version von hotplug (hotplug-2004_03_29)
leider brachte das alles nicht den gewünschten Erfolg.
In der Hoffnung, daß Ihr mir weiter helfen könnt poste ich mal die Outputs von lsmod und dmesg:
Ich bin so langsam am verzweifeln, weil ich das nicht hinbekomme
Danke schonmal für Eure Hilfe
Pedde
ich habe jetzt auch mal andere Versionen von wlan-ng ausprobiert (0.2.0 und 0.2.1-pre26) und auch ne andere Version von hotplug (hotplug-2004_03_29)
leider brachte das alles nicht den gewünschten Erfolg.
In der Hoffnung, daß Ihr mir weiter helfen könnt poste ich mal die Outputs von lsmod und dmesg:
Code: Alles auswählen
lsmod:
Module Size Used by
apm 19948 1
fm801_gp 3840 0
gameport 4736 1 fm801_gp
bt878 11188 0
via_agp 8832 1
parport_pc 33348 0
tsdev 7168 0
parport 37320 1 parport_pc
mousedev 9996 0
floppy 54992 0
psmouse 17800 0
pcspkr 3816 0
rtc 12088 0
evdev 9088 0
agpgart 31784 1 via_agp
uhci_hcd 29328 0
tuner 18320 0
tvaudio 20748 0
bttv 143052 1 bt878
video_buf 20356 1 bttv
i2c_algo_bit 8968 1 bttv
v4l2_common 6400 1 bttv
btcx_risc 4744 1 bttv
i2c_core 22416 4 tuner,tvaudio,bttv,i2c_algo_bit
snd_bt87x 13640 0
snd_fm801 18376 0
snd_pcm 85384 2 snd_bt87x,snd_fm801
snd_page_alloc 11144 2 snd_bt87x,snd_pcm
snd_tea575x_tuner 4096 1 snd_fm801
videodev 9856 2 bttv,snd_tea575x_tuner
snd_ac97_codec 59268 1 snd_fm801
snd_opl3_lib 9728 1 snd_fm801
snd_timer 23172 2 snd_pcm,snd_opl3_lib
snd_hwdep 9092 1 snd_opl3_lib
snd_mpu401_uart 7296 1 snd_fm801
snd_rawmidi 23204 1 snd_mpu401_uart
snd_seq_device 7944 2 snd_opl3_lib,snd_rawmidi
snd 50660 10 snd_bt87x,snd_fm801,snd_pcm,snd_ac97_codec,snd_opl3_lib,snd_timer,snd_hwdep,snd_mpu401_uart,snd_rawm
idi,snd_seq_device
soundcore 9824 2 bttv,snd
3c59x 36776 0
prism2_usb 69892 0
usbcore 104164 4 uhci_hcd,prism2_usb
p80211 30736 1 prism2_usb
prism54 47388 0
firmware_class 9728 1 prism54
ide_cd 38176 0
cdrom 35740 1 ide_cd
isofs 33976 0
ext3 109672 6
jbd 54552 1 ext3
ide_generic 1664 0
via82cxxx 12956 1
ide_disk 16768 9
ide_core 125028 4 ide_cd,ide_generic,via82cxxx,ide_disk
unix 26036 12
Code: Alles auswählen
dmesg:
Linux version 2.6.8 (root@linuxpc) (gcc-Version 3.3.4 (Debian 1:3.3.4-13)) #1 Fri Feb 25 12:40:55 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001c000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
448MB LOWMEM available.
On node 0 totalpages: 114688
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 110592 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI disabled because your bios is from 2000 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 534.539 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 447352k/458752k available (1210k kernel code, 10652k reserved, 682k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1048.57 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
CPU: Intel Pentium III (Katmai) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 534.0466 MHz.
..... host bus clock speed is 133.0616 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4304k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb150, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbd80
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbda8, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0596] at 0000:00:07.0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4304 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 196k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596b (rev 22) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 31536U2, ATA DISK drive
hdb: FUJITSU MPG3409AH EF, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 30015216 sectors (15367 MB) w/512KiB Cache, CHS=29777/16/63, UDMA(66)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
hdb: max request size: 128KiB
hdb: 80063424 sectors (40992 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(66)
/dev/ide/host0/bus0/target1/lun0: p1
hdc: CD-RW IDE5224, ATAPI CD/DVD-ROM drive
hdd: CRD-8482B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 840632k swap on /dev/hda7. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
Loaded prism54 driver, version 1.2
usbcore: registered new driver usbfs
usbcore: registered new driver hub
prism2_usb: no version for "p80211netdev_rx" found: kernel tainted.
prism2usb_init: prism2_usb.o: 0.2.1-pre23 Loaded
prism2usb_init: dev_info is: prism2_usb
usbcore: registered new driver prism2_usb
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
PCI: Found IRQ 9 for device 0000:00:0c.0
3c59x: Donald Becker and others. [url]www.scyld.com/network/vortex.html[/url]
0000:00:0c.0: 3Com PCI 3c905C Tornado at 0xe000. Vers LK1.1.19
Linux video capture interface: v1.00
PCI: Found IRQ 9 for device 0000:00:0b.0
PCI: Found IRQ 5 for device 0000:00:0a.1
PCI: Sharing IRQ 5 with 0000:00:0a.0
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
PCI: Found IRQ 5 for device 0000:00:0a.0
PCI: Sharing IRQ 5 with 0000:00:0a.1
bttv0: Bt878 (rev 2) at 0000:00:0a.0, irq: 5, latency: 64, mmio: 0xeb002000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00fffffb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom: model=61204, tuner=Philips FI1216 MK2 (5), radio=no
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951),ta8874z
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 10, io base 0000d400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using address 2
usb 1-2: new full speed USB device using address 3
Linux agpgart interface v0.100 (c) Dave Jones
Real Time Clock Driver v1.12
input: PC Speaker
input: GenPS/2 Genius Wheel Mouse on isa0060/serio1
inserting floppy driver for 2.6.8
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: Maximum main memory to use for agp memory: 381M
agpgart: AGP aperture is 64M @ 0xe0000000
bt878: AUDIO driver version 0.0.0 loaded
gameport: at pci0000:00:0b.1 speed 1807 kHz
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02a4a60(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
usb 1-2: USB disconnect, address 3
usb 1-2: new full speed USB device using address 4
Danke schonmal für Eure Hilfe
Pedde
Netgear MA111V2
Hallo,
da ist ja auch kein prism drin, sondern ein sis162.
Also:
Nix mit nativem Treibersupport -> ndiswrapper
MfG L.
da ist ja auch kein prism drin, sondern ein sis162.
Also:
Nix mit nativem Treibersupport -> ndiswrapper
MfG L.
--
sigs sind doof...
sigs sind doof...