Hallo liebe Gemeinde,
nach der Installation von einer aktuellen stable-CD (503) ist es mir nicht möglich per DHCP eine IP zu beziehen.
ifconfig verrät mir, daß eine Netzwerkkarte eth0 vorhanden ist, die aber über keine IP verfügt.
Weise ich der Karte mittels ifconfig eine feste Adresse zu und starte einen Ping auf meinen Router, so erscheint diese Adresse in einer Filterliste des Routers. Es ist nicht möglich andere Rechner anzupingen bzw eine Anwort auf ein Ping von betroffenen Rechner zu erhalten.
Hardwareprobleme schließe ich aus, da diverse Live-CDs und auch die Deian-Installations-CD während der Installation problemlos auf das Netz zugreifen können.
Die Netzwerkkarte ist ein Intel 82551ER PCI Fast Ethernet Controller. Die Kernelmodule e100 und mii sind geladen.
Ich auch, weil ich nicht mehr weiß wo ich noch ansetzen soll.
Bin für jeden Tip dankbar.
Gruß.
kaule
Kein Netz nach Installation
Re: Kein Netz nach Installation
Hier die Ausgabe von dhclient:
ifconfig:
/etc/network/interfaces:
Für dieses Posting benutze ich DSL-Linux. Die Konfiguration funktioniert automatisch.
Code: Alles auswählen
There is already a pid file /var/run/dhclient.pid with pid 1928
killed old client process, removed PID file
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
Listening on LPF/eth0/00:e0:4b:1a:f2:9a
Sending on LPF/eth0/00:e0:4b:1a:f2:9a
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 1
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
Code: Alles auswählen
eth0 Link encap:Ethernet Hardware Adresse 00:e0:4b:1a:f2:9a
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metrik:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:560 (560.0 B) TX bytes:560 (560.0 B)
Code: Alles auswählen
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
# allow-hotplug eth0
auto eth0
iface eth0 inet dhcp
Re: Kein Netz nach Installation
Der Vollständigkeit halber noch die Ausgabe von dmesg:
Danke für die Mühen,
Gruß,
kaule
Code: Alles auswählen
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-486 (Debian 2.6.26-19) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Wed Aug 19 05:40:02 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000cc000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000f7c0000 (usable)
[ 0.000000] BIOS-e820: 00000000fffe8000 - 0000000100000000 (reserved)
[ 0.000000] 247MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 63424) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 63424
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 63424
[ 0.000000] On node 0 totalpages: 63424
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 464 pages used for memmap
[ 0.000000] Normal zone: 58864 pages, LIFO batch:15
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321]
[ 0.000000] Allocating PCI resources starting at 10000000 (gap: 0f7c0000:f0828000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000cc000
[ 0.000000] PM: Registered nosave memory: 00000000000cc000 - 00000000000e8000
[ 0.000000] PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62928
[ 0.000000] Kernel command line: root=/dev/hda1 ro quiet
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] mapped APIC to ffffb000 (011f3000)
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 399.941 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.004000] Memory: 241688k/253696k available (1696k kernel code, 11408k reserved, 743k data, 320k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfffb3000 - 0xfffff000 ( 304 kB)
[ 0.004000] vmalloc : 0xd0000000 - 0xfffb1000 ( 767 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xcf7c0000 ( 247 MB)
[ 0.004000] .init : 0xc0364000 - 0xc03b4000 ( 320 kB)
[ 0.004000] .data : 0xc02a80a1 - 0xc0362000 ( 743 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02a80a1 (1696 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084623] Calibrating delay using timer specific routine.. 801.57 BogoMIPS (lpj=1603141)
[ 0.084823] Security Framework initialized
[ 0.084852] SELinux: Disabled at boot.
[ 0.084873] Capability LSM initialized
[ 0.084952] Mount-cache hash table entries: 512
[ 0.085488] Initializing cgroup subsys ns
[ 0.085510] Initializing cgroup subsys cpuacct
[ 0.085528] Initializing cgroup subsys devices
[ 0.085610] CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
[ 0.085634] CPU: L2 Cache: 128K (32 bytes/line)
[ 0.085673] CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02
[ 0.085715] Checking 'hlt' instruction... OK.
[ 0.107657] Freeing SMP alternatives: 0k freed
[ 0.107676] ACPI: Core revision 20080321
[ 0.107850] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321]
[ 0.107888] ACPI: Unable to load the System Description Tables
[ 0.108410] net_namespace: 652 bytes
[ 0.108441] Booting paravirtualized kernel on bare hardware
[ 0.109811] NET: Registered protocol family 16
[ 0.110964] EISA bus registered
[ 0.136988] PCI: PCI BIOS revision 2.10 entry at 0xf9ca0, last bus=0
[ 0.137011] PCI: Using configuration type 1 for base access
[ 0.137052] Setting up standard PCI resources
[ 0.146377] ACPI: Interpreter disabled.
[ 0.146398] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.146555] pnp: PnP ACPI: disabled
[ 0.146576] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.146903] PnPBIOS: Found PnP BIOS installation structure at 0xc00fa9d0
[ 0.146933] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xaa00, dseg 0xf0000
[ 0.150055] PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
[ 0.151285] PCI: Probing PCI hardware
[ 0.151304] PCI: Probing PCI hardware (bus 00)
[ 0.162173] PCI: Using IRQ router NatSemi [1022/2090] at 0000:00:0f.0
[ 0.163341] system 00:07: iomem range 0x0-0x9ffff could not be reserved
[ 0.163371] system 00:07: iomem range 0xfffc0000-0xffffffff could not be reserved
[ 0.163401] system 00:07: iomem range 0xfee00000-0xfee0ffff has been reserved
[ 0.163430] system 00:07: iomem range 0x100000-0xffffff could not be reserved
[ 0.163480] system 00:08: iomem range 0xe8000-0xeffff has been reserved
[ 0.163508] system 00:08: iomem range 0xf0000-0xf3fff could not be reserved
[ 0.163536] system 00:08: iomem range 0xf4000-0xf7fff could not be reserved
[ 0.163564] system 00:08: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.163592] system 00:08: iomem range 0xfc000-0xfffff could not be reserved
[ 0.165684] NET: Registered protocol family 2
[ 0.166184] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.167485] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.167739] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.167927] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.167947] TCP reno registered
[ 0.168282] NET: Registered protocol family 1
[ 0.168947] checking if image is initramfs... it is
[ 4.117033] Freeing initrd memory: 6034k freed
[ 4.119491] audit: initializing netlink socket (disabled)
[ 4.119544] type=2000 audit(1253564631.116:1): initialized
[ 4.119916] Total HugeTLB memory allocated, 0
[ 4.120209] VFS: Disk quotas dquot_6.5.1
[ 4.120383] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 4.120532] msgmni has been set to 484
[ 4.121022] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 4.121047] io scheduler noop registered
[ 4.121064] io scheduler anticipatory registered
[ 4.121082] io scheduler deadline registered
[ 4.121141] io scheduler cfq registered (default)
[ 4.121249] pci 0000:00:01.1: Boot video device
[ 4.121297] pci 0000:00:09.0: Firmware left e100 interrupts enabled; disabling
[ 4.139358] lxfb 0000:00:01.1: 8192 KB of video memory at 0xee000000
[ 4.163182] Console: switching to colour frame buffer device 80x30
[ 4.177340] fb0: Geode LX frame buffer device
[ 4.177952] isapnp: Scanning for PnP cards...
[ 4.534891] isapnp: No Plug & Play device found
[ 4.546740] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 4.547070] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 4.547399] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 4.549616] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 4.550194] 00:0f: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 4.557134] brd: module loaded
[ 4.557584] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[ 4.557608] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 4.558511] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.559089] mice: PS/2 mouse device common for all mice
[ 4.559591] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 4.559641] rtc0: alarms up to one day
[ 4.560246] EISA: Probing bus 0 at eisa.0
[ 4.560277] Cannot allocate resource for EISA slot 1
[ 4.560343] Cannot allocate resource for EISA slot 6
[ 4.560385] EISA: Detected 0 cards.
[ 4.560403] cpuidle: using governor ladder
[ 4.560420] cpuidle: using governor menu
[ 4.560447] No iBFT detected.
[ 4.563802] TCP cubic registered
[ 4.563821] NET: Registered protocol family 17
[ 4.563851] Using IPI Shortcut mode
[ 4.564468] registered taskstats version 1
[ 4.565113] rtc_cmos 00:03: setting system clock to 2009-09-21 20:23:52 UTC (1253564632)
[ 4.565541] Freeing unused kernel memory: 320k freed
[ 4.585527] input: AT Translated Set 2 keyboard as /class/input/input0
[ 5.244602] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 7.322466] Uniform Multi-Platform E-IDE driver
[ 7.322495] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 7.418508] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 7.418532] e100: Copyright(c) 1999-2006 Intel Corporation
[ 7.418720] PCI: setting IRQ 11 as level-triggered
[ 7.418741] PCI: Found IRQ 11 for device 0000:00:09.0
[ 7.419059] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 7.444964] e100: eth0: e100_probe: addr 0xeffff000, irq 11, MAC addr 00:e0:4b:1a:f2:9a
[ 7.772030] AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller
[ 7.772061] AMD5536: IDE controller (0x1022:0x209a rev 0x01) at PCI slot 0000:00:0f.2
[ 7.772271] AMD5536: not 100% native mode: will probe irqs later
[ 7.772468] AMD5536: IDE port disabled
[ 7.772518] ide0: BM-DMA at 0xfe00-0xfe07
[ 7.772543] Probing IDE interface ide0...
[ 7.836378] usbcore: registered new interface driver usbfs
[ 7.836523] usbcore: registered new interface driver hub
[ 7.836714] usbcore: registered new device driver usb
[ 7.856879] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.060252] hda: TOSHIBA MK2018GAP, ATA DISK drive
[ 8.508252] hdb: HL-DT-STDVD-ROM GDR8164B, ATAPI CD/DVD-ROM drive
[ 8.564274] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 8.564531] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 8.564556] hda: UDMA/33 mode selected
[ 8.564780] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 8.565427] hdb: UDMA/33 mode selected
[ 8.566007] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 8.579219] PCI: Found IRQ 11 for device 0000:00:0f.4
[ 8.579457] PCI: Sharing IRQ 11 with 0000:00:0f.5
[ 8.579547] PCI: Setting latency timer of device 0000:00:0f.4 to 64
[ 8.579593] ohci_hcd 0000:00:0f.4: OHCI Host Controller
[ 8.579941] ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 1
[ 8.580005] ohci_hcd 0000:00:0f.4: irq 11, io mem 0xefffe000
[ 8.644693] SCSI subsystem initialized
[ 8.651098] usb usb1: configuration #1 chosen from 1 choice
[ 8.651295] hub 1-0:1.0: USB hub found
[ 8.651341] hub 1-0:1.0: 4 ports detected
[ 8.733656] libata version 3.00 loaded.
[ 8.752721] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.752751] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.752775] usb usb1: Product: OHCI Host Controller
[ 8.752795] usb usb1: Manufacturer: Linux 2.6.26-2-486 ohci_hcd
[ 8.752815] usb usb1: SerialNumber: 0000:00:0f.4
[ 8.753196] PCI: Found IRQ 11 for device 0000:00:0f.5
[ 8.753403] PCI: Sharing IRQ 11 with 0000:00:0f.4
[ 8.753524] PCI: Setting latency timer of device 0000:00:0f.5 to 64
[ 8.753571] ehci_hcd 0000:00:0f.5: EHCI Host Controller
[ 8.753705] ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 2
[ 8.776326] ehci_hcd 0000:00:0f.5: irq 11, io mem 0xefffd000
[ 8.788113] ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 8.788522] usb usb2: configuration #1 chosen from 1 choice
[ 8.788723] hub 2-0:1.0: USB hub found
[ 8.788765] hub 2-0:1.0: 4 ports detected
[ 8.892592] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.892620] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.892644] usb usb2: Product: EHCI Host Controller
[ 8.892663] usb usb2: Manufacturer: Linux 2.6.26-2-486 ehci_hcd
[ 8.892684] usb usb2: SerialNumber: 0000:00:0f.5
[ 9.228512] hda: max request size: 128KiB
[ 9.553222] hda: 39070080 sectors (20003 MB), CHS=38760/16/63
[ 9.553334] hda: cache flushes supported
[ 9.553519] hda: hda1 hda2 < hda5 >
[ 9.589020] hdb: ATAPI 52X DVD-ROM drive, 256kB Cache
[ 9.589055] Uniform CD-ROM driver Revision: 3.20
[ 10.220673] PM: Starting manual resume from disk
[ 10.391100] kjournald starting. Commit interval 5 seconds
[ 10.391147] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.769026] udevd version 125 started
[ 18.713640] input: PC Speaker as /class/input/input1
[ 20.889180] AMD Geode RNG detected
[ 20.945573] cs5535_gpio: base=0x6100 mask=0xb003c66 major=251
[ 21.625603] PCI: setting IRQ 10 as level-triggered
[ 21.625629] PCI: Assigned IRQ 10 for device 0000:00:01.2
[ 21.625722] PCI: Sharing IRQ 10 with 0000:00:01.1
[ 21.625914] geode-aes: GEODE AES engine enabled.
[ 21.975639] Error: Driver 'pcspkr' is already registered, aborting...
[ 24.247921] Adding 730916k swap on /dev/hda5. Priority:-1 extents:1 across:730916k
[ 24.863725] EXT3 FS on hda1, internal journal
[ 25.779422] loop: module loaded
[ 26.007620] eepro100.c:v1.09j-t 9/29/99 Donald Becker
[ 26.007634] eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
[ 28.104507] e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex
Gruß,
kaule
Re: Kein Netz nach Installation
Du könntest mal versuchen das Netzwerk manuell zu setzen. Gehen wir von einem Router mit IP 192.168.1.1 aus. Falls es abweicht, bitte anpassen.
Und nun:
Code: Alles auswählen
ifconfig eth0 192.168.1.2 netmask 255.255.255.0 up
Code: Alles auswählen
ifconfig eth0
ping 192.168.1.1
arp -a
Re: Kein Netz nach Installation
Halloele,
nach der manuellen Konfiguration der Karte mit ifconfig sieht es so aus:
Der ping auf den Router endet mit "host unreachable".
arp -a sagt:
Ich suche eine Richtung, in die ich weiter suchen kann. Könnte es am fehlenden Powermanagement des Rechners liegen? Gibt es noch andere Möglichkeiten die Karte oder das Netzwerk zu parametrieren?
Gruß,
kaule
nach der manuellen Konfiguration der Karte mit ifconfig sieht es so aus:
Code: Alles auswählen
eth0 Link encap:Ethernet Hardware Adresse 00:e0:4b:1a:f2:9a
inet Adresse:192.168.42.10 Bcast:192.168.42.255 Maske:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
arp -a sagt:
Code: Alles auswählen
? (192.168.42.254) auf <unvollständig> auf eth0
Gruß,
kaule