Bin gerade auf einer Konferenz in Tokyo und brauche dringend Internet um wenigstens ab und zu mal mit meiner Frau zu sprechen. Das hat die letzten Tage auch schoen geklappt, hier gibts nen Router mit Kabel, das stecke ich ein und alles funktioniert.
Ja, bis heute. Heute funktioniert naemlich nix mehr (bin jetzt an einem oeffentlichen Rechner). Nichts wurde am Setup veraendert, ich sass am selben Platz und benutzte sogar genau das selbe Kabel wie gestern. Aber es geht halt nicht.
Konnte in dmesg keine anderen Meldungen erkennen als gestern; generell finde ich ueberhaupt keine Fehlermeldungen zum Netzwerk. Die Laempchen am Router blinken auch lustig und zeigen Aktivitaet an, funktionieren tuts trotzdem nicht.
Ach ja, gestern habe ich ein "aptitude upgrade full" gemacht, erneuert wurden libmozirgendwas und xulrunner. Danach ging es aber immer noch, deshalb glaube ich eigentlich nicht, dass es daran liegt.
Irgendwelche Tips, was ich mal versuchen koennte?
EDIT:
Hier mal der output von ifconfig
Code: Alles auswählen
eth0 Link encap:Ethernet Hardware Adresse 00:03:0d:37:7e:fe
inet6-Adresse: fe80::203:dff:fe37:7efe/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:933 errors:0 dropped:0 overruns:0 frame:0
TX packets:88 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:98579 (96.2 KiB) TX bytes:10071 (9.8 KiB)
Interrupt:19 Basisadresse:0xd800
eth0:avahi Link encap:Ethernet Hardware Adresse 00:03:0d:37:7e:fe
inet Adresse:169.254.7.177 Bcast:169.254.255.255 Maske:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
Interrupt:19 Basisadresse:0xd800
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:16436 Metrik:1
RX packets:58 errors:0 dropped:0 overruns:0 frame:0
TX packets:58 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:4556 (4.4 KiB) TX bytes:4556 (4.4 KiB)
Code: Alles auswählen
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-17) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 21 04:57:38 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000002dfd0000 (usable)
[ 0.000000] BIOS-e820: 000000002dfd0000 - 000000002dfdf000 (ACPI data)
[ 0.000000] BIOS-e820: 000000002dfdf000 - 000000002e000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 735MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.000000] Entering add_active_range(0, 0, 188368) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 188368
[ 0.000000] HighMem 188368 -> 188368
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 188368
[ 0.000000] On node 0 totalpages: 188368
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1440 pages used for memmap
[ 0.000000] Normal zone: 182832 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000F7670, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 2DFD0000, 0030 (r1 A M I OEMRSDT 5000530 MSFT 97)
[ 0.000000] ACPI: FACP 2DFD0200, 0081 (r2 A M I OEMFACP 5000530 MSFT 97)
[ 0.000000] ACPI: DSDT 2DFD03F0, 34F6 (r1 255KI 255KI000 0 INTL 2002026)
[ 0.000000] ACPI: FACS 2DFDF000, 0040
[ 0.000000] ACPI: APIC 2DFD0390, 0054 (r1 A M I OEMAPIC 5000530 MSFT 97)
[ 0.000000] ACPI: OEMB 2DFDF040, 0109 (r1 A M I AMI_OEM 5000530 MSFT 97)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 2, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ10 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 2e000000:d1f80000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186896
[ 0.000000] Kernel command line: root=/dev/hda1 ro quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 798.265 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 735940k/753472k available (1769k kernel code, 17016k reserved, 751k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xee800000 - 0xff7fe000 ( 271 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xedfd0000 ( 735 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba66b - 0xc0376620 ( 751 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba66b (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084206] Calibrating delay using timer specific routine.. 1598.02 BogoMIPS (lpj=3196041)
[ 0.084274] Security Framework initialized
[ 0.084282] SELinux: Disabled at boot.
[ 0.084289] Capability LSM initialized
[ 0.084317] Mount-cache hash table entries: 512
[ 0.084551] Initializing cgroup subsys ns
[ 0.084558] Initializing cgroup subsys cpuacct
[ 0.084564] Initializing cgroup subsys devices
[ 0.084595] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.084602] CPU: L2 Cache: 256K (64 bytes/line)
[ 0.084608] Intel machine check architecture supported.
[ 0.084615] Intel machine check reporting enabled on CPU#0.
[ 0.084636] Checking 'hlt' instruction... OK.
[ 0.100610] SMP alternatives: switching to UP code
[ 0.114609] Freeing SMP alternatives: 16k freed
[ 0.114617] ACPI: Core revision 20080321
[ 0.124826] ENABLING IO-APIC IRQs
[ 0.125030] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.164730] CPU0: AMD Mobile AMD Sempron(tm) Processor 2800+ stepping 02
[ 0.168010] Brought up 1 CPUs
[ 0.168010] Total of 1 processors activated (1598.02 BogoMIPS).
[ 0.168010] CPU0 attaching sched-domain:
[ 0.168010] domain 0: span 0
[ 0.168010] groups: 0
[ 0.168010] net_namespace: 660 bytes
[ 0.168010] Booting paravirtualized kernel on bare hardware
[ 0.168010] NET: Registered protocol family 16
[ 0.168010] ACPI: bus type pci registered
[ 0.168010] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[ 0.168010] PCI: Using configuration type 1 for base access
[ 0.168010] Setting up standard PCI resources
[ 0.180011] ACPI: EC: Look up EC in DSDT
[ 0.184011] ACPI: Interpreter enabled
[ 0.184011] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.184011] ACPI: Using IOAPIC for interrupt routing
[ 0.188172] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.206250] ACPI: EC: GPE = 0x2, I/O: command/status = 0x66, data = 0x62
[ 0.206257] ACPI: EC: driver started in interrupt mode
[ 0.206427] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.206649] pci 0000:00:02.0: Enabling SiS 96x SMBus
[ 0.207481] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.253540] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.253750] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 0.253952] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 0.254154] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 0.254355] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 5 7 10 11 12 14 15)
[ 0.254561] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 7 10 11 12 14 15)
[ 0.254765] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.254968] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 0.255256] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 05, should be FE [20080321]
[ 0.255272] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.255329] pnp: PnP ACPI init
[ 0.255348] ACPI: bus type pnp registered
[ 0.258885] pnp: PnP ACPI: found 10 devices
[ 0.258892] ACPI: ACPI bus type pnp unregistered
[ 0.258899] PnPBIOS: Disabled by ACPI PNP
[ 0.259346] PCI: Using ACPI for IRQ routing
[ 0.259675] system 00:07: ioport range 0x480-0x48f has been reserved
[ 0.259683] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.259690] system 00:07: ioport range 0x800-0x87f has been reserved
[ 0.259697] system 00:07: ioport range 0x880-0x8ff has been reserved
[ 0.259704] system 00:07: ioport range 0xc00-0xc1f has been reserved
[ 0.259714] system 00:07: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.259722] system 00:07: iomem range 0xffe80000-0xffefffff has been reserved
[ 0.259730] system 00:07: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.259747] system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.259755] system 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.259772] system 00:09: iomem range 0x0-0x9ffff could not be reserved
[ 0.259780] system 00:09: iomem range 0xc0000-0xd0fff could not be reserved
[ 0.259788] system 00:09: iomem range 0xe0000-0xfffff could not be reserved
[ 0.259795] system 00:09: iomem range 0x100000-0x2fffffff could not be reserved
[ 0.290578] PCI: Bridge: 0000:00:01.0
[ 0.290585] IO window: c000-cfff
[ 0.290592] MEM window: 0xdfe00000-0xdfefffff
[ 0.290600] PREFETCH window: 0x00000000cfd00000-0x00000000dfcfffff
[ 0.290609] PCI: Bus 2, cardbus bridge: 0000:00:09.0
[ 0.290614] IO window: 0x00001000-0x000010ff
[ 0.290621] IO window: 0x00001400-0x000014ff
[ 0.290627] PREFETCH window: 0x30000000-0x33ffffff
[ 0.290634] MEM window: 0x34000000-0x37ffffff
[ 0.290641] PCI: Bus 6, cardbus bridge: 0000:00:09.1
[ 0.290646] IO window: 0x00001800-0x000018ff
[ 0.290652] IO window: 0x00001c00-0x00001cff
[ 0.290659] PREFETCH window: 0x38000000-0x3bffffff
[ 0.290666] MEM window: 0x3c000000-0x3fffffff
[ 0.290696] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.290715] ACPI: PCI Interrupt 0000:00:09.1[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.290762] NET: Registered protocol family 2
[ 0.290936] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.291538] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.293091] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.293867] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.293874] TCP reno registered
[ 0.294050] NET: Registered protocol family 1
[ 0.294272] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 0.940268] it is
[ 1.638423] Freeing initrd memory: 7027k freed
[ 1.639593] audit: initializing netlink socket (disabled)
[ 1.639615] type=2000 audit(1248832273.636:1): initialized
[ 1.639805] Total HugeTLB memory allocated, 0
[ 1.639927] VFS: Disk quotas dquot_6.5.1
[ 1.639992] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.640067] msgmni has been set to 1451
[ 1.640295] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.640303] io scheduler noop registered
[ 1.640307] io scheduler anticipatory registered
[ 1.640312] io scheduler deadline registered
[ 1.640336] io scheduler cfq registered (default)
[ 1.702408] pci 0000:01:00.0: Boot video device
[ 1.703019] isapnp: Scanning for PnP cards...
[ 2.054573] isapnp: No Plug & Play device found
[ 2.059301] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 2.060100] ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.060113] ACPI: PCI interrupt for device 0000:00:02.6 disabled
[ 2.062685] brd: module loaded
[ 2.062864] PNP: PS/2 Controller [PNP030b:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.067852] i8042.c: Detected active multiplexing controller, rev 1.0.
[ 2.068759] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.068769] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.068776] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.068782] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.068788] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.069061] mice: PS/2 mouse device common for all mice
[ 2.069557] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 2.069579] rtc0: alarms up to one month
[ 2.069643] cpuidle: using governor ladder
[ 2.069648] cpuidle: using governor menu
[ 2.069657] No iBFT detected.
[ 2.070765] TCP cubic registered
[ 2.070772] NET: Registered protocol family 17
[ 2.070782] Using IPI No-Shortcut mode
[ 2.071016] registered taskstats version 1
[ 2.071261] rtc_cmos 00:02: setting system clock to 2009-07-29 01:51:15 UTC (1248832275)
[ 2.071520] Freeing unused kernel memory: 244k freed
[ 2.078413] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.310944] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.311031] ACPI: ACPI0007:00 is registered as cooling_device0
[ 2.313897] Marking TSC unstable due to: TSC halts in idle.
[ 2.314585] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 2.315071] ACPI: Thermal Zone [THRM] (28 C)
[ 3.203612] No dock devices found.
[ 3.316514] SCSI subsystem initialized
[ 3.464128] libata version 3.00 loaded.
[ 3.586811] Uniform Multi-Platform E-IDE driver
[ 3.586823] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 3.593789] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
[ 3.593799] SIS5513: IDE controller (0x1039:0x5513 rev 0x00) at PCI slot 0000:00:02.5
[ 3.593814] SIS5513: not 100% native mode: will probe irqs later
[ 3.593832] ide0: BM-DMA at 0xffa0-0xffa7
[ 3.593845] ide1: BM-DMA at 0xffa8-0xffaf
[ 3.593854] Probing IDE interface ide0...
[ 3.888198] hda: TOSHIBA MK4025GAS, ATA DISK drive
[ 3.983405] usbcore: registered new interface driver usbfs
[ 3.983456] usbcore: registered new interface driver hub
[ 3.983525] usbcore: registered new device driver usb
[ 4.003947] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.007473] sis900.c: v1.08.10 Apr. 2 2006
[ 4.560214] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 4.560272] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 4.560279] hda: UDMA/33 mode selected
[ 4.560322] Probing IDE interface ide1...
[ 5.296315] hdc: PHILIPS CD-RW/DVD-ROM SCB5265, ATAPI CD/DVD-ROM drive
[ 5.968227] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.968424] hdc: UDMA/33 mode selected
[ 5.968610] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 6.017793] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.018000] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 6.018000] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 6.018000] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 6.018000] ohci_hcd 0000:00:03.0: irq 20, io mem 0xdfffd000
[ 6.074272] usb usb1: configuration #1 chosen from 1 choice
[ 6.074331] hub 1-0:1.0: USB hub found
[ 6.074348] hub 1-0:1.0: 3 ports detected
[ 6.176214] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.176222] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.176228] usb usb1: Product: OHCI Host Controller
[ 6.176233] usb usb1: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 6.176238] usb usb1: SerialNumber: 0000:00:03.0
[ 6.176310] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 6.176333] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 6.176384] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 6.176411] ohci_hcd 0000:00:03.1: irq 21, io mem 0xdfffe000
[ 6.234177] usb usb2: configuration #1 chosen from 1 choice
[ 6.234238] hub 2-0:1.0: USB hub found
[ 6.234256] hub 2-0:1.0: 3 ports detected
[ 6.336218] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.336226] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.336232] usb usb2: Product: OHCI Host Controller
[ 6.336237] usb usb2: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 6.336243] usb usb2: SerialNumber: 0000:00:03.1
[ 6.336347] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 23
[ 6.336371] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 6.336418] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 3
[ 6.336472] PCI: cache line size of 64 is not supported by device 0000:00:03.3
[ 6.336493] ehci_hcd 0000:00:03.3: irq 23, io mem 0xdffff000
[ 6.348034] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 6.348168] usb usb3: configuration #1 chosen from 1 choice
[ 6.348224] hub 3-0:1.0: USB hub found
[ 6.348244] hub 3-0:1.0: 6 ports detected
[ 6.452194] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.452201] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.452207] usb usb3: Product: EHCI Host Controller
[ 6.452212] usb usb3: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 6.452217] usb usb3: SerialNumber: 0000:00:03.3
[ 6.452292] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 6.453632] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
[ 6.464465] 0000:00:04.0: Using transceiver found at address 1 as default
[ 6.465775] eth0: SiS 900 PCI Fast Ethernet at 0xd800, IRQ 19, 00:03:0d:37:7e:fe
[ 6.465885] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 6.515775] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[dfffb800-dfffbfff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 6.633132] hda: max request size: 128KiB
[ 6.637409] hda: 78140160 sectors (40007 MB), CHS=65535/16/63
[ 6.641212] hda: cache flushes supported
[ 6.641288] hda: hda1 hda2 < hda5 hda6 >
[ 6.729045] hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
[ 6.729061] Uniform CD-ROM driver Revision: 3.20
[ 7.336236] PM: Starting manual resume from disk
[ 7.460962] kjournald starting. Commit interval 5 seconds
[ 7.460982] EXT3-fs: mounted filesystem with ordered data mode.
[ 7.788351] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00030d53255ec409]
[ 9.480485] udevd version 125 started
[ 11.812732] Linux agpgart interface v0.103
[ 11.834315] agpgart: Detected SiS chipset - id:1888
[ 11.834743] agpgart: AGP aperture is 4M @ 0xe0000000
[ 11.954418] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 11.972548] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.066159] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[ 12.871450] Yenta: CardBus bridge found at 0000:00:09.0 [1584:3008]
[ 12.871475] Yenta O2: res at 0x94/0xD4: 00/ea
[ 12.871481] Yenta O2: enabling read prefetch/write burst
[ 13.008556] Yenta: ISA IRQ mask 0x0ab8, PCI irq 17
[ 13.008564] Socket status: 30000006
[ 13.032821] Yenta: CardBus bridge found at 0000:00:09.1 [1584:3008]
[ 13.041550] input: Power Button (FF) as /class/input/input1
[ 13.068866] ACPI: Power Button (FF) [PWRF]
[ 13.069033] input: Lid Switch as /class/input/input2
[ 13.084210] ACPI: Lid Switch [LID]
[ 13.084364] input: Sleep Button (CM) as /class/input/input3
[ 13.112161] ACPI: Sleep Button (CM) [SLPB]
[ 13.112316] input: Power Button (CM) as /class/input/input4
[ 13.140093] ACPI: Power Button (CM) [PWRB]
[ 13.165002] Yenta: ISA IRQ mask 0x0ab8, PCI irq 17
[ 13.165010] Socket status: 30000006
[ 13.860840] ACPI: AC Adapter [AC0] (on-line)
[ 13.919870] ACPI: Battery Slot [BAT0] (battery absent)
[ 14.027901] ACPI: device:04 is registered as cooling_device1
[ 14.028156] input: Video Bus as /class/input/input5
[ 14.055416] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 15.576110] input: PC Speaker as /class/input/input6
[ 17.034762] cs: IO port probe 0x100-0x3af: clean.
[ 17.036614] cs: IO port probe 0x3e0-0x4ff: clean.
[ 17.037348] cs: IO port probe 0x820-0x8ff: clean.
[ 17.037417] cs: IO port probe 0xc00-0xcf7: clean.
[ 17.038356] cs: IO port probe 0xa00-0xaff: clean.
[ 17.040003] cs: IO port probe 0x100-0x3af: clean.
[ 17.041867] cs: IO port probe 0x3e0-0x4ff: clean.
[ 17.042599] cs: IO port probe 0x820-0x8ff: clean.
[ 17.042667] cs: IO port probe 0xc00-0xcf7: clean.
[ 17.043416] cs: IO port probe 0xa00-0xaff: clean.
[ 17.561135] ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 18
[ 17.577780] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x6eb1, caps: 0xa04711/0x40a
[ 17.617540] input: SynPS/2 Synaptics TouchPad as /class/input/input7
[ 17.686321] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 18.512034] intel8x0_measure_ac97_clock: measured 55300 usecs
[ 18.512042] intel8x0: clocking to 48000
[ 19.628644] Adding 1389580k swap on /dev/hda5. Priority:-1 extents:1 across:1389580k
[ 20.043781] EXT3 FS on hda1, internal journal
[ 20.443586] loop: module loaded
[ 21.305328] kjournald starting. Commit interval 5 seconds
[ 21.308195] EXT3 FS on hda6, internal journal
[ 21.308205] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.624300] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 2800+ processors (1 cpu cores) (version 2.20.00)
[ 24.624355] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0xa
[ 24.624362] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x13
[ 24.788159] Clocksource tsc unstable (delta = 161392534 ns)
[ 24.849057] eth0: Media Link On 100mbps full-duplex
[ 26.075565] lp: driver loaded but no devices found
[ 26.090784] ppdev: user-space parallel port driver
[ 26.942577] NET: Registered protocol family 10
[ 26.943669] lo: Disabled Privacy Extensions
[ 31.964878] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 31.964890] vboxdrv: Successfully done.
[ 31.964896] vboxdrv: Found 1 processor cores.
[ 31.965029] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 31.965035] vboxdrv: Successfully loaded version 2.1.4 (interface 0x000a0009).
[ 35.368168] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 37.784013] eth0: no IPv6 routers present
[ 76.656568] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
