dongle probing not supported

[Longshengs]

Hallo!
Habe bereits kurz danach gesucht, ich hoffe jedoch, ich habe nichts übersehen. Google konnte mir leider nicht helfen. Ich habe hier eben bei mir einen kleinen Home Server mit Debian aufgesetzt.

Beim Booten erhalte ich immer die folgende Meldung:

via-ircc: dongle probing not supported, please specify dongle_id module parameter.

Wie kann ich diese Fehlermeldung beseitigen? Hier die gesamte dmesg:

[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-486 (Debian 2.6.26-17) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Sun Jun 21 04:15:19 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000f7f0000 (usable)
[ 0.000000] BIOS-e820: 000000000f7f0000 - 000000000f7f3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000000f7f3000 - 000000000f800000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 247MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 63472) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 63472
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 63472
[ 0.000000] On node 0 totalpages: 63472
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 464 pages used for memmap
[ 0.000000] Normal zone: 58912 pages, LIFO batch:15
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP 000F6240, 0014 (r0 VIA601)
[ 0.000000] ACPI: RSDT 0F7F3000, 0028 (r1 VIA601 AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 0F7F3040, 0074 (r1 VIA601 AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 0F7F30C0, 2370 (r1 VIA601 AWRDACPI 1000 MSFT 100000D)
[ 0.000000] ACPI: FACS 0F7F0000, 0040
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] Allocating PCI resources starting at 10000000 (gap: 0f800000:f07f0000)
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62976
[ 0.000000] Kernel command line: root=/dev/hda1 ro quiet
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] mapped APIC to ffffb000 (011f3000)
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 533.376 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.004000] Memory: 241580k/253888k available (1695k kernel code, 11652k reserved, 744k data, 320k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfffb3000 - 0xfffff000 ( 304 kB)
[ 0.004000] vmalloc : 0xd0000000 - 0xfffb1000 ( 767 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xcf7f0000 ( 247 MB)
[ 0.004000] .init : 0xc0364000 - 0xc03b4000 ( 320 kB)
[ 0.004000] .data : 0xc02a7d83 - 0xc0362000 ( 744 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02a7d83 (1695 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084600] Calibrating delay using timer specific routine.. 1068.73 BogoMIPS (lpj=2137462)
[ 0.084825] Security Framework initialized
[ 0.084853] SELinux: Disabled at boot.
[ 0.084877] Capability LSM initialized
[ 0.084950] Mount-cache hash table entries: 512
[ 0.085712] Initializing cgroup subsys ns
[ 0.085734] Initializing cgroup subsys cpuacct
[ 0.085751] Initializing cgroup subsys devices
[ 0.085835] CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
[ 0.085858] CPU: L2 Cache: 64K (32 bytes/line)
[ 0.085926] CPU: Centaur VIA Samuel 2 stepping 03
[ 0.085964] Checking 'hlt' instruction... OK.
[ 0.109225] Freeing SMP alternatives: 0k freed
[ 0.109249] ACPI: Core revision 20080321
[ 0.120726] ACPI: setting ELCR to 0020 (from 1c20)
[ 0.128567] net_namespace: 652 bytes
[ 0.128607] Booting paravirtualized kernel on bare hardware
[ 0.130096] NET: Registered protocol family 16
[ 0.131319] EISA bus registered
[ 0.131380] ACPI: bus type pci registered
[ 0.150691] PCI: PCI BIOS revision 2.10 entry at 0xfb180, last bus=1
[ 0.150712] PCI: Using configuration type 1 for base access
[ 0.150770] Setting up standard PCI resources
[ 0.158648] ACPI: EC: Look up EC in DSDT
[ 0.175941] ACPI: Interpreter enabled
[ 0.175962] ACPI: (supports S0 S1 S4 S5)
[ 0.176070] ACPI: Using PIC for interrupt routing
[ 0.194834] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.196101] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.247744] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.248563] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.249476] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 0.250395] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
[ 0.251121] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.251294] pnp: PnP ACPI init
[ 0.251339] ACPI: bus type pnp registered
[ 0.265318] pnp: PnP ACPI: found 12 devices
[ 0.265340] ACPI: ACPI bus type pnp unregistered
[ 0.265366] PnPBIOS: Disabled by ACPI PNP
[ 0.266752] PCI: Using ACPI for IRQ routing
[ 0.267496] ACPI: RTC can wake from S4
[ 0.267648] system 00:00: iomem range 0xf0000-0xf3fff could not be reserved
[ 0.267676] system 00:00: iomem range 0xf4000-0xf7fff could not be reserved
[ 0.267703] system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.267730] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
[ 0.267758] system 00:00: iomem range 0xf7f0000-0xf7fffff could not be reserved
[ 0.267787] system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
[ 0.267814] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.267841] system 00:00: iomem range 0x100000-0xf7effff could not be reserved
[ 0.267869] system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.267925] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.300155] PCI: Bridge: 0000:00:01.0
[ 0.300170] IO window: disabled.
[ 0.300192] MEM window: 0xe8000000-0xeaffffff
[ 0.300213] PREFETCH window: 0x0000000010000000-0x00000000100fffff
[ 0.300261] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.300393] NET: Registered protocol family 2
[ 0.300899] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.302198] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.302823] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.303174] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.303193] TCP reno registered
[ 0.303629] NET: Registered protocol family 1
[ 0.304405] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 1.931673] it is
[ 3.858822] Freeing initrd memory: 6038k freed
[ 3.861344] audit: initializing netlink socket (disabled)
[ 3.861420] type=2000 audit(1248296975.860:1): initialized
[ 3.861915] Total HugeTLB memory allocated, 0
[ 3.862243] VFS: Disk quotas dquot_6.5.1
[ 3.862433] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.862622] msgmni has been set to 484
[ 3.863261] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.863286] io scheduler noop registered
[ 3.863303] io scheduler anticipatory registered
[ 3.863320] io scheduler deadline registered
[ 3.863374] io scheduler cfq registered (default)
[ 3.863434] PCI: VIA PCI bridge detected.Disabling DAC.
[ 3.863563] pci 0000:01:00.0: Boot video device
[ 3.865459] isapnp: Scanning for PnP cards...
[ 4.220056] isapnp: No Plug & Play device found
[ 4.234052] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 4.234432] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 4.237038] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 4.245218] brd: module loaded
[ 4.245725] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 4.245751] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 4.246281] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.246950] mice: PS/2 mouse device common for all mice
[ 4.247593] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 4.247644] rtc0: alarms up to one year, y3k
[ 4.248354] EISA: Probing bus 0 at eisa.0
[ 4.248416] Cannot allocate resource for EISA slot 4
[ 4.248478] EISA: Detected 0 cards.
[ 4.248496] cpuidle: using governor ladder
[ 4.248514] cpuidle: using governor menu
[ 4.248542] No iBFT detected.
[ 4.251465] TCP cubic registered
[ 4.251483] NET: Registered protocol family 17
[ 4.251517] Using IPI Shortcut mode
[ 4.252276] registered taskstats version 1
[ 4.252941] rtc_cmos 00:04: setting system clock to 2009-07-22 21:09:37 UTC (1248296977)
[ 4.256388] Freeing unused kernel memory: 320k freed
[ 4.278543] input: AT Translated Set 2 keyboard as /class/input/input0
[ 4.941747] ACPI: PNP0C0B:00 is registered as cooling_device0
[ 4.941788] ACPI: Fan [FAN] (on)
[ 4.974235] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 4.974489] ACPI: ACPI0007:00 is registered as cooling_device1
[ 4.974519] ACPI: Processor [CPU0] (supports 2 throttling states)
[ 4.986047] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 4.986794] ACPI: Thermal Zone [THRM] (32 C)
[ 7.615776] No dock devices found.
[ 7.836977] SCSI subsystem initialized
[ 8.116076] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 8.116111] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 8.118370] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 8.118392] PCI: setting IRQ 11 as level-triggered
[ 8.118412] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 8.123986] eth0: VIA Rhine II at 0x1e800, 00:40:63:d9:9f:de, IRQ 11.
[ 8.127081] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
[ 8.432377] usbcore: registered new interface driver usbfs
[ 8.432540] usbcore: registered new interface driver hub
[ 8.432796] usbcore: registered new device driver usb
[ 8.442198] USB Universal Host Controller Interface driver v3.0
[ 8.444621] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
[ 8.444644] PCI: setting IRQ 12 as level-triggered
[ 8.444663] ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 8.444718] uhci_hcd 0000:00:11.2: UHCI Host Controller
[ 8.445240] uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
[ 8.445315] uhci_hcd 0000:00:11.2: irq 12, io base 0x0000d400
[ 8.445959] usb usb1: configuration #1 chosen from 1 choice
[ 8.446150] hub 1-0:1.0: USB hub found
[ 8.446218] hub 1-0:1.0: 2 ports detected
[ 8.548882] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.548913] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.548936] usb usb1: Product: UHCI Host Controller
[ 8.548954] usb usb1: Manufacturer: Linux 2.6.26-2-486 uhci_hcd
[ 8.548975] usb usb1: SerialNumber: 0000:00:11.2
[ 8.549116] ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
[ 8.549173] uhci_hcd 0000:00:11.3: UHCI Host Controller
[ 8.549375] uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
[ 8.549452] uhci_hcd 0000:00:11.3: irq 12, io base 0x0000d800
[ 8.550108] usb usb2: configuration #1 chosen from 1 choice
[ 8.550304] hub 2-0:1.0: USB hub found
[ 8.550387] hub 2-0:1.0: 2 ports detected
[ 8.652729] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.652761] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.652785] usb usb2: Product: UHCI Host Controller
[ 8.652803] usb usb2: Manufacturer: Linux 2.6.26-2-486 uhci_hcd
[ 8.652824] usb usb2: SerialNumber: 0000:00:11.3
[ 9.797495] libata version 3.00 loaded.
[ 10.072212] Uniform Multi-Platform E-IDE driver
[ 10.072245] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 10.087812] FDC 0 is a post-1991 82077
[ 10.430665] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:11.1
[ 10.430739] VP_IDE: not 100% native mode: will probe irqs later
[ 10.430828] VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1
[ 10.430856] VP_IDE: IDE port disabled
[ 10.430882] ide0: BM-DMA at 0xd000-0xd007
[ 10.430916] Probing IDE interface ide0...
[ 10.856314] hda: WDC WD400EB-00CPF0, ATA DISK drive
[ 10.905019] Marking TSC unstable due to: TSC halts in idle.
[ 11.304247] hdb: PLEXTOR CD-R PREMIUM, ATAPI CD/DVD-ROM drive
[ 11.360269] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 11.361181] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 11.361204] hda: UDMA/33 mode selected
[ 11.362120] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 11.362216] hdb: UDMA/33 mode selected
[ 11.362379] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 11.606503] hda: max request size: 128KiB
[ 11.624733] hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63
[ 11.624773] hda: cache flushes not supported
[ 11.625024] hda: hda1 hda2 < hda5 >
[ 11.683865] hdb: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache
[ 11.683907] Uniform CD-ROM driver Revision: 3.20
[ 12.096121] PM: Starting manual resume from disk
[ 12.266399] kjournald starting. Commit interval 5 seconds
[ 12.266452] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.082655] udevd version 125 started
[ 21.283590] input: PC Speaker as /class/input/input1
[ 24.944535] Linux agpgart interface v0.103
[ 25.265896] agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset
[ 25.275666] agpgart: AGP aperture is 128M @ 0xe0000000
[ 25.597660] NET: Registered protocol family 23
[ 26.249738] via-ircc: dongle probing not supported, please specify dongle_id module parameter.
[ 26.251813] IrDA: Registered device irda0 (via-ircc)
[ 26.496691] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 26.726248] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 27.925761] parport_pc: VIA 686A/8231 detected
[ 27.925783] parport_pc: probing current configuration
[ 27.925816] parport_pc: Current parallel port base: 0x378
[ 27.925886] parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
[ 28.242459] parport_pc: VIA parallel port: io=0x378, irq=7
[ 31.232588] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 31.232614] PCI: setting IRQ 10 as level-triggered
[ 31.232634] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 31.232843] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 33.423935] input: Power Button (FF) as /class/input/input2
[ 33.531192] ACPI: Power Button (FF) [PWRF]
[ 33.531638] input: Power Button (CM) as /class/input/input3
[ 33.553224] ACPI: Power Button (CM) [PWRB]
[ 41.032715] Adding 722884k swap on /dev/hda5. Priority:-1 extents:1 across:722884k
[ 41.484116] EXT3 FS on hda1, internal journal
[ 42.521237] loop: module loaded
[ 44.714839] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1

[habakug]

Hallo!

Die Meldung kommt vom via-ircc-Modul [1]:

Code: Alles auswählen

 * Function via_ircc_read_dongle_id (void)
*
*/
static int via_ircc_read_dongle_id(int iobase)
{
         int dongle_id = 9;      /* Default to IBM */
        IRDA_ERROR("via-ircc: dongle probing not supported, please specify dongle_id module parameter.\n");
        return dongle_id;
}

Das Modul bedient einen Chip auf deinem Motherboard.

VIA VT8231/VT1211 SIR/MIR/FIR
Say Y here if you want to build support for the VIA VT8231
and VIA VT1211 IrDA controllers, found on the motherboards using
those VIA chipsets. To use this controller, you will need
to plug a specific 5 pins FIR IrDA dongle in the specific
motherboard connector. The driver provides support for SIR, MIR
and FIR (4Mbps) speeds.

You will need to specify the 'dongle_id' module parameter to
indicate the FIR dongle attached to the controller.

Du brauchst also einen "specific 5 pins FIR IrDA dongle", dessen ID du dem Modul übergibst. Hast du keinen, kannst du die Meldung ignorieren

Gruß, habakug

[1] http://lxr.free-electrons.com/source/dr ... via-ircc.c
[2] http://kernel.org/doc/menuconfig/driver ... onfig.html

[Longshengs]

Ah..Ok vielen Dank dir! Vor allem für die schnelle Antwort. Dachte nur, man kann die Meldung ausblenden oder derartiges. Damit der Server n bisschen schneller bootet Aber ok. Ist auch so schnell genug *g*