Seine Funktion: CW-Server, 24x7Tg Betrieb. Nach einer Neu-installation (Devian-Etch) nun dies:
Soll ich sie entsorgen, was meint ihr?
Code: Alles auswählen
shog:~# smartctl --all /dev/hdc
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K80 family
Device Model: HTS548080M9AT00
Serial Number: MRL442L4HB949B
Firmware Version: MG4OA53A
User Capacity: 80'026'361'856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Wed Feb 4 10:33:38 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 55) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 105 105 040 Pre-fail Offline - 4587
3 Spin_Up_Time 0x0007 206 206 033 Pre-fail Always - 2
4 Start_Stop_Count 0x0012 096 096 000 Old_age Always - 6517
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 128 128 040 Pre-fail Offline - 36
9 Power_On_Hours 0x0012 072 072 000 Old_age Always - 12295
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 4065
191 G-Sense_Error_Rate 0x000a 097 097 000 Old_age Always - 327681
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 161
193 Load_Cycle_Count 0x0012 077 077 000 Old_age Always - 235261
194 Temperature_Celsius 0x0002 152 152 000 Old_age Always - 36 (Lifetime Min/Max 4/2286)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 37
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 45 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 45 occurred at disk power-on lifetime: 12292 hours (512 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 f3 e4 0d e0 Error: UNC 2 sectors at LBA = 0x000de4f3 = 910579
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 02 f3 e4 0d e0 00 00:02:06.300 READ DMA EXT
25 00 08 17 71 0e e0 00 00:02:06.300 READ DMA EXT
25 00 12 05 71 0e e0 00 00:02:06.300 READ DMA EXT
25 00 08 fd 70 0e e0 00 00:02:06.300 READ DMA EXT
25 00 02 f7 64 0e e0 00 00:02:06.300 READ DMA EXT
Error 44 occurred at disk power-on lifetime: 12292 hours (512 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 f3 e4 0d e0 Error: UNC 2 sectors at LBA = 0x000de4f3 = 910579
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 02 f3 e4 0d e0 00 00:01:23.100 READ DMA EXT
25 00 08 17 71 0e e0 00 00:01:23.100 READ DMA EXT
25 00 12 05 71 0e e0 00 00:01:23.100 READ DMA EXT
25 00 08 fd 70 0e e0 00 00:01:23.100 READ DMA EXT
25 00 02 f7 64 0e e0 00 00:01:23.100 READ DMA EXT
Error 43 occurred at disk power-on lifetime: 12292 hours (512 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 75 02 6c 0b e0 Error: UNC 117 sectors at LBA = 0x000b6c02 = 748546
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 77 6b 0b e0 00 00:01:35.700 READ DMA EXT
25 00 4c 1b 6b 0b e0 00 00:01:35.500 READ DMA EXT
25 00 0c 0f 6b 0b e0 00 00:01:35.500 READ DMA EXT
25 00 06 07 6b 0b e0 00 00:01:35.500 READ DMA EXT
25 00 02 05 6b 0b e0 00 00:01:35.500 READ DMA EXT
Error 42 occurred at disk power-on lifetime: 12292 hours (512 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 fe e2 ac e0 Error: UNC 1 sectors at LBA = 0x00ace2fe = 11330302
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f7 e2 ac e0 00 19d+03:35:37.100 READ DMA EXT
25 00 58 77 b1 9f e0 00 19d+03:35:37.100 READ DMA EXT
25 00 08 67 b1 9f e0 00 19d+03:35:37.100 READ DMA EXT
25 00 08 57 b1 9f e0 00 19d+03:35:37.100 READ DMA EXT
25 00 20 6f 28 76 e0 00 19d+03:35:37.100 READ DMA EXT
Error 41 occurred at disk power-on lifetime: 12292 hours (512 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 fe e2 ac e0 Error: UNC 1 sectors at LBA = 0x00ace2fe = 11330302
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f7 e2 ac e0 00 19d+03:35:32.700 READ DMA EXT
25 00 08 97 26 76 e0 00 19d+03:35:32.600 READ DMA EXT
25 00 40 27 75 fe e0 00 19d+03:35:32.600 READ DMA EXT
35 00 08 e7 3e cd e0 00 19d+03:35:32.600 WRITE DMA EXT
35 00 08 e7 e2 a4 e0 00 19d+03:35:32.600 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 11355 -
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.