Debian startet nur noch Shell

[Eibi]

Hallo zusammen

Ich dachte nun sei alles in Ordnung, aber ich hab mich getäuscht.
Gestern wurde mein Problem mit den Abhängigkeiten (zu lesen hier) ja endlich aus der Welt geschafft, ich hab gestern noch lange am PC gesessen. Heute morgen will ich ihn hochfahren, da geht dann plötzlich nix mehr, am Ende des Bootens steht nur ein Login im Bootbildschirm und nach dem Login hab ich nur die shell zur Verfügung, also nix grafisches.
(Hoffe ihr versteht was ich meine).

Ich denke das beste wäre es, wenn ich erstmal die Codes auf dem Bootbildschirm hier poste, jedoch weiss ich nicht wie ich die irgendwie speichern oder auch nur scrollen kann...
Das wäre mal der erste Schritt!
Was würde der Diagnose weiterhelfen? (Es müsste ja eigentlich irgendwo an gnome fackeln)

[MarkusF]

Ich denke das beste wäre es, wenn ich erstmal die Codes auf dem Bootbildschirm hier poste, jedoch weiss ich nicht wie ich die irgendwie speichern oder auch nur scrollen kann...
Das wäre mal der erste Schritt!

Code: Alles auswählen

# dmesg >datei

schreibt dir die Bootmeldungen in 'datei'.

Ansonsten kannst du noch

Code: Alles auswählen

# /etc/init.d/kdm restart probieren 

bei KDE, bzw. gdm bei Gnome. Das wäre dann ein manueller Start von x

Grüße, Markus

[datoo]

es sieht so aus als wenn Gnome deinstalliert wurde (apt-get war der Meinung das du das nicht mehr brauchst )
wenn du da nicht eingeschritten bist ...
Das Gute daran du kannst Gnome natürlich wieder installieren.

Code: Alles auswählen

root:# apt-get install gdm gnome-desktop-environment

[Eibi]

es sieht so aus als wenn Gnome deinstalliert wurde (apt-get war der Meinung das du das nicht mehr brauchst )
wenn du da nicht eingeschritten bist ...
Das Gute daran du kannst Gnome natürlich wieder installieren.

Code: Alles auswählen

root:# apt-get install gdm gnome-desktop-environment

Irgendsowas hab ich mir schon fast gedacht, denn beim manuell starten kannte er "gdm" als befehl gar nicht...

Die dmesg habe ich jetzt mal geschafft zu sichern:

Code: Alles auswählen

D cache: 32K
[    0.004000] CPU: L2 cache: 3072K
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 3
[    0.004000] Intel machine check architecture supported.
[    0.004000] Intel machine check reporting enabled on CPU#3.
[    0.368565] CPU3: Intel(R) Core(TM)2 Quad  CPU   Q9300  @ 2.50GHz stepping 07
[    0.368579] Total of 4 processors activated (20003.57 BogoMIPS).
[    0.368714] ENABLING IO-APIC IRQs
[    0.368869] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.412025] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.412089] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[    0.416100] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[    0.420060] Brought up 4 CPUs
[    0.420095] CPU0 attaching sched-domain:
[    0.420097]  domain 0: span 03
[    0.420098]   groups: 01 02
[    0.420100]   domain 1: span 0f
[    0.420101]    groups: 03 0c
[    0.420104] CPU1 attaching sched-domain:
[    0.420105]  domain 0: span 03
[    0.420106]   groups: 02 01
[    0.420108]   domain 1: span 0f
[    0.420109]    groups: 03 0c
[    0.420111] CPU2 attaching sched-domain:
[    0.420113]  domain 0: span 0c
[    0.420114]   groups: 04 08
[    0.420116]   domain 1: span 0f
[    0.420117]    groups: 0c 03
[    0.420119] CPU3 attaching sched-domain:
[    0.420120]  domain 0: span 0c
[    0.420122]   groups: 08 04
[    0.420124]   domain 1: span 0f
[    0.420125]    groups: 0c 03
[    0.420498] net_namespace: 548 bytes
[    0.420508] Booting paravirtualized kernel on bare hardware
[    0.420753] NET: Registered protocol family 16
[    0.421025] ACPI: bus type pci registered
[    0.421140] PCI: Using MMCONFIG for extended config space
[    0.421142] PCI: Using configuration type 1
[    0.421161] Setting up standard PCI resources
[    0.423444] ACPI: EC: Look up EC in DSDT
[    0.427451] ACPI: Interpreter enabled
[    0.427454] ACPI: (supports S0 S3 S4 S5)
[    0.427466] ACPI: Using IOAPIC for interrupt routing
[    0.432235] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.432867] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[    0.432871] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.433505] PCI: Transparent bridge - 0000:00:1e.0
[    0.433529] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.433676] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[    0.433742] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
[    0.433811] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[    0.433876] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[    0.446438] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    0.446517] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.446595] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[    0.446672] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.446749] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    0.446827] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    0.446904] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[    0.446981] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.447209] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.447256] pnp: PnP ACPI init
[    0.447260] ACPI: bus type pnp registered
[    0.449923] pnp: PnP ACPI: found 16 devices
[    0.449925] ACPI: ACPI bus type pnp unregistered
[    0.449928] PnPBIOS: Disabled by ACPI PNP
[    0.450318] PCI: Using ACPI for IRQ routing
[    0.450320] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[    0.460064] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.460068] hpet0: 4 64-bit timers, 14318180 Hz
[    0.461109] ACPI: RTC can wake from S4
[    0.468067] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[    0.468070] system 00:01: ioport range 0x290-0x29f has been reserved
[    0.468072] system 00:01: ioport range 0x800-0x87f has been reserved
[    0.468075] system 00:01: ioport range 0x290-0x294 has been reserved
[    0.468077] system 00:01: ioport range 0x880-0x88f has been reserved
[    0.468085] system 00:0c: ioport range 0x400-0x4bf could not be reserved
[    0.468090] system 00:0d: iomem range 0xf0000000-0xf3ffffff could not be reserved
[    0.468097] system 00:0e: iomem range 0xcdc00-0xcffff has been reserved
[    0.468100] system 00:0e: iomem range 0xf0000-0xf7fff could not be reserved
[    0.468102] system 00:0e: iomem range 0xf8000-0xfbfff could not be reserved
[    0.468105] system 00:0e: iomem range 0xfc000-0xfffff could not be reserved
[    0.468107] system 00:0e: iomem range 0x7fee0000-0x7fefffff could not be reserved
[    0.468110] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[    0.468112] system 00:0e: iomem range 0x100000-0x7fedffff could not be reserved
[    0.468115] system 00:0e: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.468118] system 00:0e: iomem range 0xfed10000-0xfed1dfff could not be reserved
[    0.468120] system 00:0e: iomem range 0xfed20000-0xfed8ffff could not be reserved
[    0.468123] system 00:0e: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.468125] system 00:0e: iomem range 0xffb00000-0xffb7ffff could not be reserved
[    0.468128] system 00:0e: iomem range 0xfff00000-0xffffffff could not be reserved
[    0.468130] system 00:0e: iomem range 0xe0000-0xeffff has been reserved
[    0.498715] PCI: Bridge: 0000:00:01.0
[    0.498717]   IO window: a000-afff
[    0.498720]   MEM window: 0xf4000000-0xf7ffffff
[    0.498722]   PREFETCH window: 0x00000000e0000000-0x00000000efffffff
[    0.498725] PCI: Bridge: 0000:00:1c.0
[    0.498727]   IO window: 9000-9fff
[    0.498730]   MEM window: disabled.
[    0.498732]   PREFETCH window: disabled.
[    0.498737] PCI: Bridge: 0000:00:1c.3
[    0.498738]   IO window: b000-bfff
[    0.498742]   MEM window: 0xfc000000-0xfc0fffff
[    0.498744]   PREFETCH window: disabled.
[    0.498749] PCI: Bridge: 0000:00:1c.4
[    0.498750]   IO window: c000-cfff
[    0.498754]   MEM window: 0xf8000000-0xf9ffffff
[    0.498757]   PREFETCH window: 0x0000000080000000-0x00000000800fffff
[    0.498761] PCI: Bridge: 0000:00:1e.0
[    0.498763]   IO window: d000-dfff
[    0.498766]   MEM window: 0xfa000000-0xfbffffff
[    0.498769]   PREFETCH window: 0x0000000080100000-0x00000000801fffff
[    0.498780] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.498783] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.498796] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.498799] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.498812] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[    0.498816] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    0.498828] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
[    0.498832] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[    0.498839] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.498889] NET: Registered protocol family 2
[    0.120033] Switched to high resolution mode on CPU 1
[    0.100015] Switched to high resolution mode on CPU 2
[    0.080013] Switched to high resolution mode on CPU 3
[    0.504062] Switched to high resolution mode on CPU 0
[    0.512116] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.512343] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.512618] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.512746] TCP: Hash tables configured (established 131072 bind 65536)
[    0.512748] TCP reno registered
[    0.520201] checking if image is initramfs... it is
[    0.862643] Freeing initrd memory: 5584k freed
[    0.084011] audit: initializing netlink socket (disabled)
[    0.084011] type=2000 audit(1217164628.864:1): initialized
[    0.084011] highmem bounce pool size: 64 pages
[    0.084011] Total HugeTLB memory allocated, 0
[    0.084011] VFS: Disk quotas dquot_6.5.1
[    0.084011] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.084011] io scheduler noop registered
[    0.084011] io scheduler anticipatory registered
[    0.084011] io scheduler deadline registered
[    0.084011] io scheduler cfq registered (default)
[    0.084011] pci 0000:01:00.0: Boot video device
[    0.084011] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.084011] assign_interrupt_mode Found MSI capability
[    0.084011] Allocate Port Service[0000:00:01.0:pcie00]
[    0.084011] Allocate Port Service[0000:00:01.0:pcie03]
[    0.084011] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.084011] assign_interrupt_mode Found MSI capability
[    0.084011] Allocate Port Service[0000:00:1c.0:pcie00]
[    0.084011] Allocate Port Service[0000:00:1c.0:pcie02]
[    0.084051] Allocate Port Service[0000:00:1c.0:pcie03]
[    0.084139] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    0.084163] assign_interrupt_mode Found MSI capability
[    0.084186] Allocate Port Service[0000:00:1c.3:pcie00]
[    0.084230] Allocate Port Service[0000:00:1c.3:pcie02]
[    0.084279] Allocate Port Service[0000:00:1c.3:pcie03]
[    0.084366] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[    0.084390] assign_interrupt_mode Found MSI capability
[    0.084414] Allocate Port Service[0000:00:1c.4:pcie00]
[    0.084457] Allocate Port Service[0000:00:1c.4:pcie02]
[    0.084506] Allocate Port Service[0000:00:1c.4:pcie03]
[    0.084904] isapnp: Scanning for PnP cards...
[    0.437727] isapnp: No Plug & Play device found
[    0.441823] hpet_resources: 0xfed00000 is busy
[    0.441897] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    0.442041] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.442612] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.444031] brd: module loaded
[    0.444154] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.108984] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.108988] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.109086] mice: PS/2 mouse device common for all mice
[    0.109128] cpuidle: using governor ladder
[    0.109130] cpuidle: using governor menu
[    0.109415] TCP cubic registered
[    0.109428] NET: Registered protocol family 1
[    0.109439] NET: Registered protocol family 17
[    0.109444] Using IPI No-Shortcut mode
[    0.109575] registered taskstats version 1
[    0.109716] Freeing unused kernel memory: 252k freed
[    0.125640] input: AT Translated Set 2 keyboard as /class/input/input0
[    0.927439] ACPI: ACPI0007:00 is registered as cooling_device0
[    0.927443] ACPI: Processor [CPU0] (supports 8 throttling states)
[    0.927558] ACPI: SSDT 7FEE8300, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20040311)
[    0.162671] ACPI: ACPI0007:01 is registered as cooling_device1
[    0.162675] ACPI: Processor [CPU1] (supports 8 throttling states)
[    0.162791] ACPI: SSDT 7FEE8390, 0087 (r1  PmRef  Cpu2Ist     3000 INTL 20040311)
[    0.448034] ACPI: ACPI0007:02 is registered as cooling_device2
[    0.448034] ACPI: Processor [CPU2] (supports 8 throttling states)
[    0.448034] ACPI: SSDT 7FEE8420, 0087 (r1  PmRef  Cpu3Ist     3000 INTL 20040311)
[    0.895819] ACPI: ACPI0007:03 is registered as cooling_device3
[    0.895823] ACPI: Processor [CPU3] (supports 8 throttling states)
[    0.236136] usbcore: registered new interface driver usbfs
[    0.236154] usbcore: registered new interface driver hub
[    0.240131] usbcore: registered new device driver usb
[    0.240945] USB Universal Host Controller Interface driver v3.0
[    0.240990] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.240998] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[    0.241001] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.241084] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    0.241108] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e000
[    0.241190] usb usb1: configuration #1 chosen from 1 choice
[    0.241206] hub 1-0:1.0: USB hub found
[    0.241210] hub 1-0:1.0: 2 ports detected
[    0.291885] No dock devices found.
[    0.308414] SCSI subsystem initialized
[    0.322244] libata version 3.00 loaded.
[    1.107521] Floppy drive(s): fd0 is 1.44M
[    0.344089] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    0.344092] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.344094] usb usb1: Product: UHCI Host Controller
[    0.344096] usb usb1: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    0.344097] usb usb1: SerialNumber: 0000:00:1a.0
[    0.344129] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[    0.344137] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[    0.344139] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.344157] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[    0.344182] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000e100
[    0.344258] usb usb2: configuration #1 chosen from 1 choice
[    0.344274] hub 2-0:1.0: USB hub found
[    0.344278] hub 2-0:1.0: 2 ports detected
[    1.127747] FDC 0 is a post-1991 82077
[    0.384100] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.384103] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.384106] usb usb2: Product: UHCI Host Controller
[    0.384107] usb usb2: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    0.384109] usb usb2: SerialNumber: 0000:00:1a.1
[    0.384137] ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
[    0.384150] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[    0.384152] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    0.384170] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[    0.384193] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000e500
[    0.384272] usb usb3: configuration #1 chosen from 1 choice
[    0.384290] hub 3-0:1.0: USB hub found
[    0.384294] hub 3-0:1.0: 2 ports detected
[    0.400030] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.400030] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.400030] usb usb3: Product: UHCI Host Controller
[    0.400030] usb usb3: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    0.400030] usb usb3: SerialNumber: 0000:00:1a.2
[    0.400030] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[    0.400030] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    0.400030] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.400030] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[    0.400030] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e200
[    0.400030] usb usb4: configuration #1 chosen from 1 choice
[    0.400030] hub 4-0:1.0: USB hub found
[    0.400030] hub 4-0:1.0: 2 ports detected
[    1.160106] usb 1-2: new full speed USB device using uhci_hcd and address 2
[    0.400079] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.400081] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.400083] usb usb4: Product: UHCI Host Controller
[    0.400085] usb usb4: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    0.400087] usb usb4: SerialNumber: 0000:00:1d.0
[    0.400107] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[    0.400113] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    0.400116] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.400140] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[    0.400166] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e300
[    0.400235] usb usb5: configuration #1 chosen from 1 choice
[    0.400251] hub 5-0:1.0: USB hub found
[    0.400254] hub 5-0:1.0: 2 ports detected
[    1.136089] usb 1-2: configuration #1 chosen from 1 choice
[    0.672048] usb 1-2: New USB device found, idVendor=07d1, idProduct=f101
[    0.672048] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    0.672048] usb 1-2: Product: D-Link DBT-122
[    0.672048] usb 1-2: Manufacturer: Broadcom Corp
[    0.416088] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.416090] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.416093] usb usb5: Product: UHCI Host Controller
[    0.416094] usb usb5: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    0.416096] usb usb5: SerialNumber: 0000:00:1d.1
[    0.416117] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[    0.416123] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    0.416126] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.416147] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[    0.416180] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e400
[    0.416250] usb usb6: configuration #1 chosen from 1 choice
[    0.416266] hub 6-0:1.0: USB hub found
[    0.416271] hub 6-0:1.0: 2 ports detected
[    0.432083] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    0.432086] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.432088] usb usb6: Product: UHCI Host Controller
[    0.432089] usb usb6: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    0.432091] usb usb6: SerialNumber: 0000:00:1d.2
[    0.700050] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[    0.700050] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.700050] PCI: Setting latency timer of device 0000:04:00.0 to 64
[    0.700050] eth0: RTL8168b/8111b at 0xf881a000, 00:1d:7d:a7:66:1c, XID 38000000 IRQ 219
[    0.700061] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[    0.700077] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 20 (level, low) -> IRQ 20
[    0.700247] eth1: RTL8169sb/8110sb at 0xf884c000, 00:80:5a:69:26:b0, XID 10000000 IRQ 20
[    0.437274] ahci 0000:03:00.0: version 3.0
[    0.437294] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[    0.772061] usb 4-1: new full speed USB device using uhci_hcd and address 2
[    0.776055] usb 4-1: configuration #1 chosen from 1 choice
[    0.791444] usb 4-1: New USB device found, idVendor=0bda, idProduct=0111
[    0.791447] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    0.791448] usb 4-1: Product: USB 2.0 Reader
[    0.791450] usb 4-1: Manufacturer: Generic
[    0.791451] usb 4-1: SerialNumber: 071029014067000464
[    0.791574] Initializing USB Mass Storage driver...
[    0.791685] scsi0 : SCSI emulation for USB Mass Storage devices
[    1.269302] usb-storage: device found at 2
[    1.269304] usb-storage: waiting for device to settle before scanning
[    0.791758] usbcore: registered new interface driver usb-storage
[    0.791765] USB Mass Storage support registered.
[    0.564073] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[    0.564077] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
[    0.564083] PCI: Setting latency timer of device 0000:03:00.0 to 64
[    0.564226] scsi1 : ahci
[    0.564285] scsi2 : ahci
[    0.564334] ata1: SATA max UDMA/133 abar m8192@0xfc000000 port 0xfc000100 irq 19
[    0.564337] ata2: SATA max UDMA/133 abar m8192@0xfc000000 port 0xfc000180 irq 19
[    0.856078] ata1: SATA link down (SStatus 0 SControl 300)
[    1.340130] ata2: SATA link down (SStatus 0 SControl 300)
[    0.864060] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[    0.864060] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[    0.864060] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    0.864060] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
[    0.866601] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[    0.866606] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc105000
[    0.590120] Uniform Multi-Platform E-IDE driver
[    0.590123] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    0.880070] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    0.880166] usb usb7: configuration #1 chosen from 1 choice
[    0.880192] hub 7-0:1.0: USB hub found
[    0.880196] hub 7-0:1.0: 6 ports detected
[    0.892114] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[    0.892117] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.892119] usb usb7: Product: EHCI Host Controller
[    0.892121] usb usb7: Manufacturer: Linux 2.6.25-2-686 ehci_hcd
[    0.892122] usb usb7: SerialNumber: 0000:00:1a.7
[    1.272098] ata_piix 0000:00:1f.2: version 2.12
[    1.272098] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[    1.272098] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[    1.272098] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    1.272098] scsi3 : ata_piix
[    1.272098] scsi4 : ata_piix
[    1.272260] ata3: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[    1.272263] ata4: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[    0.916076] hub 7-0:1.0: unable to enumerate USB device on port 2
[    0.916132] usb 1-2: USB disconnect, address 2
[    1.420139] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    0.632045] ata3.00: HPA detected: current 976771055, native 976773168
[    0.632045] ata3.00: ATA-8: SAMSUNG HD501LJ, CR100-13, max UDMA7
[    0.632045] ata3.00: 976771055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.944071] usb 1-2: new full speed USB device using uhci_hcd and address 3
[    1.428117] ata3.00: configured for UDMA/133
[    0.956066] usb 1-2: configuration #1 chosen from 1 choice
[    0.956066] usb 1-2: New USB device found, idVendor=07d1, idProduct=f101
[    0.956066] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    0.956066] usb 1-2: Product: D-Link DBT-122
[    0.956066] usb 1-2: Manufacturer: Broadcom Corp
[    1.028085] ata4: SATA link down (SStatus 0 SControl 300)
[    1.326247] scsi 3:0:0:0: Direct-Access     ATA      SAMSUNG HD501LJ  CR10 PQ: 0 ANSI: 5
[    1.326322] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 19
[    1.326326] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[    1.326355] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[    1.326387] scsi5 : ata_piix
[    1.326421] scsi6 : ata_piix
[    1.326861] ata5: SATA max UDMA/133 cmd 0xe700 ctl 0xe800 bmdma 0xeb00 irq 19
[    1.326864] ata6: SATA max UDMA/133 cmd 0xe900 ctl 0xea00 bmdma 0xeb08 irq 19
[    1.524145] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.540302] ata5.00: ATAPI: ATAPI   DVD A  DH20A1S, UX14, max UDMA/100
[    1.556306] ata5.00: configured for UDMA/100
[    1.608154] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.620304] ata6.00: ATAPI: TSSTcorpDVD-ROM SH-D163B, SB01, max UDMA/33
[    1.632311] ata6.00: configured for UDMA/33
[    0.700049] scsi 5:0:0:0: CD-ROM            ATAPI    DVD A  DH20A1S   UX14 PQ: 0 ANSI: 5
[    1.340103] scsi 6:0:0:0: CD-ROM            TSSTcorp DVD-ROM SH-D163B SB01 PQ: 0 ANSI: 5
[    1.048072] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[    1.048072] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    1.048072] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    1.048072] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[    1.050023] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    1.050028] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc104000
[    1.060078] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    1.060167] usb usb8: configuration #1 chosen from 1 choice
[    1.060189] hub 8-0:1.0: USB hub found
[    1.060198] hub 8-0:1.0: 6 ports detected
[    1.068127] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[    1.068130] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.068132] usb usb8: Product: EHCI Host Controller
[    1.068134] usb usb8: Manufacturer: Linux 2.6.25-2-686 ehci_hcd
[    1.068135] usb usb8: SerialNumber: 0000:00:1d.7
[    1.352103] ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 18 (level, low) -> IRQ 18
[    1.400147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:02.0
[    0.752163] JMB: IDE controller (0x197b:0x2363 rev 0x02) at  PCI slot 0000:03:00.1
[    0.752185] PCI: Enabling device 0000:03:00.1 (0000 -> 0001)
[    0.752190] ACPI: PCI Interrupt 0000:03:00.1[B] -> GSI 16 (level, low) -> IRQ 16
[    0.752197] JMB: 100% native mode on irq 16
[    0.752213] PCI: Setting latency timer of device 0000:03:00.1 to 64
[    0.752218]     ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:PIO
[    0.752230]     ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:PIO, hdd:PIO
[    0.752240] Probing IDE interface ide0...
[    1.705257] Driver 'sd' needs updating - please use bus_type methods
[    1.705318] sd 3:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
[    1.705328] sd 3:0:0:0: [sda] Write Protect is off
[    1.705330] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.705345] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.705384] sd 3:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
[    1.705393] sd 3:0:0:0: [sda] Write Protect is off
[    1.705394] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.705409] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.705411]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[    1.144078]  sda1 sda2 sda3 < sda5 >
[    1.436109] sd 3:0:0:0: [sda] Attached SCSI disk
[    1.146399] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.146402] Uniform CD-ROM driver Revision: 3.20
[    1.146443] sr 5:0:0:0: Attached scsi CD-ROM sr0
[    1.444109] sr1: scsi3-mmc drive: 4x/48x cd/rw xa/form2 cdda tray
[    1.444109] sr 6:0:0:0: Attached scsi CD-ROM sr1
[    1.159416] sd 3:0:0:0: Attached scsi generic sg0 type 0
[    1.159432] sr 5:0:0:0: Attached scsi generic sg1 type 5
[    1.159445] sr 6:0:0:0: Attached scsi generic sg2 type 5
[    0.844072] usb 8-1: new high speed USB device using ehci_hcd and address 2
[    0.864497] hda: WDC WD3000JB-00KFA0, ATA DISK drive
[    1.792141] usb 8-1: configuration #1 chosen from 1 choice
[    0.884061] scsi7 : SCSI emulation for USB Mass Storage devices
[    1.504113] usb-storage: device found at 2
[    1.504113] usb-storage: waiting for device to settle before scanning
[    0.884061] usb 8-1: New USB device found, idVendor=0bda, idProduct=0111
[    0.884061] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    0.884061] usb 8-1: Product: USB 2.0 Reader
[    0.884061] usb 8-1: Manufacturer: Generic
[    0.884061] usb 8-1: SerialNumber: 071029014067000464
[    0.884061] usb 4-1: USB disconnect, address 2
[    0.976090] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[    0.976181] hda: UDMA/100 mode selected
[    0.976264] Probing IDE interface ide1...
[    1.036083] ide0 at 0xb000-0xb007,0xb102 on irq 16
[    1.861198] hda: max request size: 512KiB
[    1.864655] hda: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63
[    1.548232] hda: cache flushes supported
[    1.548261]  hda: hda1
[    1.588119] PM: Starting manual resume from disk
[    1.592119] kjournald starting.  Commit interval 5 seconds
[    1.106124] EXT3-fs: mounted filesystem with ordered data mode.
[    2.490498] input: Power Button (FF) as /class/input/input1
[    2.512198] ACPI: Power Button (FF) [PWRF]
[    2.512244] input: Power Button (CM) as /class/input/input2
[    2.542937] ACPI: Power Button (CM) [PWRB]
[    2.513655] input: PC Speaker as /class/input/input3
[    2.574928] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[    2.574982] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0460)
[    2.575006] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    2.194826] Linux agpgart interface v0.103
[    1.993141] Real Time Clock Driver v1.12ac
[    2.662435] Bluetooth: Core ver 2.11
[    2.662525] NET: Registered protocol family 31
[    2.662527] Bluetooth: HCI device and connection manager initialized
[    2.662529] Bluetooth: HCI socket layer initialized
[    2.028442] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
[    2.091463] Bluetooth: HCI USB driver ver 2.9
[    2.717924] usbcore: registered new interface driver hci_usb
[    2.164143] logips2pp: Detected unknown logitech mouse model 116
[    2.424983] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[    2.424999] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[    2.169303] b43-phy0: Broadcom 4318 WLAN found
[    2.204432] phy0: Selected rate control algorithm 'pid'
[    2.230424] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[    3.364240] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input4
[    2.580047] parport_pc 00:09: reported by Plug and Play ACPI
[    2.580113] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[    3.651454] Adding 2658716k swap on /dev/sda5.  Priority:-1 extents:1 across:2658716k
[    2.568169] usb-storage: device scan complete
[    3.271972] scsi 7:0:0:0: Direct-Access     Generic  2.0 Reader-CF    1.00 PQ: 0 ANSI: 0 CCS
[    3.698955] EXT3 FS on sda2, internal journal
[    3.292228] scsi 7:0:0:1: Direct-Access     Generic  2.0 Reader-Multi 1.00 PQ: 0 ANSI: 0 CCS
[    2.979038] loop: module loaded
[    2.760181] fuse init (API version 7.9)
[    3.916268] sd 7:0:0:0: [sdb] 3914064 512-byte hardware sectors (2004 MB)
[    3.916268] sd 7:0:0:0: [sdb] Write Protect is off
[    3.916268] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
[    3.916268] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[    3.919233] sd 7:0:0:0: [sdb] 3914064 512-byte hardware sectors (2004 MB)
[    3.920085] sd 7:0:0:0: [sdb] Write Protect is off
[    3.920088] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
[    3.920090] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[    3.920133]  sdb: sdb1
[    3.920268] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[    3.920268] sd 7:0:0:0: Attached scsi generic sg3 type 0
[    3.328267] sd 7:0:0:1: [sdc] Attached SCSI removable disk
[    3.328297] sd 7:0:0:1: Attached scsi generic sg4 type 0
[    5.636386] lp0: using parport0 (interrupt-driven).
[    5.640781] ppdev: user-space parallel port driver
[    5.192802] NET: Registered protocol family 10
[    5.193235] lo: Disabled Privacy Extensions
[    4.765157] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[    5.179995] input: b43-phy0 as /class/input/input5
[    5.296344] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[    5.296344] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[    5.680373] r8169: eth1: link down
[    5.680373] ADDRCONF(NETDEV_UP): eth1: link is not ready
[    6.959811] r8169: eth0: link up
[    6.959818] r8169: eth0: link up
[    7.336497] eth0: no IPv6 routers present

Vielleicht hilft die noch zusätzlich weiter, aber ich versuch erstmal gnome nochmal zu installieren.

Wie bringe ich apt dazu, sich die Dateien gefälligst von der Debian-CD zu holen?

[lottikarotti]

Die Apt-Quellen sind ja hier zu finden:
/etc/apt/sources.lst

Mit freundlichen Grüßen, lottikarotti.

[Eibi]

Hat sich eh erledigt mit der CD, ich hab vergessen dass die pppoe-Befehle noch gingen, auch wenn sich pppoe-config selbst nicht mehr starten ließ.
Hat alles wieder funktioniert und alles wieder so wies sein soll.
Wieder was gelernt,
Muchas gracias!