System bleibt hin+wieder kurz haengen

Twilo · Beitrag von **Twilo** » 21.03.2008 14:22:23

mein System Debian lenny bleibt hin+wieder kurz hängen
auf der 1. Konsole bzw. in der kern.log erscheint dann ziemlich oft folgende Fehlermeldung

Code: Alles auswählen

Mar 21 14:08:47 kay-desktop kernel: ata1: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x7 next cpb idx 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 0: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 1: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 2: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 3: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 4: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 5: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 6: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: CPB 7: ctl_flags 0x1f, resp_flags 0x0
Mar 21 14:08:47 kay-desktop kernel: ata1: timeout waiting for ADMA IDLE, stat=0x400
Mar 21 14:08:47 kay-desktop kernel: ata1: timeout waiting for ADMA LEGACY, stat=0x400
Mar 21 14:08:47 kay-desktop kernel: ata1.00: NCQ disabled due to excessive errors
Mar 21 14:08:47 kay-desktop kernel: ata1.00: exception Emask 0x0 SAct 0xff SErr 0x0 action 0x2 frozen
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 61/10:00:c7:9b:82/00:00:23:00:00/40 tag 0 cdb 0x0 data 8192 out
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 61/20:08:22:ff:73/00:00:18:00:00/40 tag 1 cdb 0x0 data 16384 out
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 60/08:10:47:e1:86/00:00:00:00:00/40 tag 2 cdb 0x0 data 4096 in
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 61/f0:18:c7:88:09/00:00:00:00:00/40 tag 3 cdb 0x0 data 122880 out
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 61/e8:20:df:86:09/01:00:00:00:00/40 tag 4 cdb 0x0 data 249856 out
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 61/e8:28:f7:84:09/01:00:00:00:00/40 tag 5 cdb 0x0 data 249856 out
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 61/38:30:d7:dd:61/01:00:0d:00:00/40 tag 6 cdb 0x0 data 159744 out
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: cmd 61/00:38:d7:db:61/02:00:0d:00:00/40 tag 7 cdb 0x0 data 262144 out
Mar 21 14:08:47 kay-desktop kernel:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 21 14:08:47 kay-desktop kernel: ata1: soft resetting port
Mar 21 14:08:47 kay-desktop kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 21 14:08:47 kay-desktop kernel: ata1.00: configured for UDMA/133
Mar 21 14:08:47 kay-desktop kernel: ata1: EH complete
Mar 21 14:08:47 kay-desktop kernel: sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
Mar 21 14:08:47 kay-desktop kernel: sd 0:0:0:0: [sda] Write Protect is off
Mar 21 14:08:47 kay-desktop kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Mar 21 14:08:47 kay-desktop kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

was könnte das sein?

Code: Alles auswählen

hdparm /dev/sda

/dev/sda:
 IO_support    =  0 (default)
16-bit)
 HDIO_GET_UNMASKINTR failed: Inappropriate ioctl for device
 HDIO_GET_DMA failed: Inappropriate ioctl for device
 HDIO_GET_KEEPSETTINGS failed: Inappropriate ioctl for device
 readonly      =  0 (off)
 readahead     = 256 (on)
 geometry      = 48641/255/63, sectors = 781422768, start = 0

Code: Alles auswählen

hdparm -i /dev/sda

/dev/sda:

 Model=SAMSUNG HD401LJ                         , FwRev=ZZ100-14, SerialNo=S0HVJ1UL602083
 Config={ Fixed }
 RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
 BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=?1?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=781422768
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: unknown:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

Code: Alles auswählen

hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media
        Model Number:       SAMSUNG HD401LJ
        Serial Number:      S0HVJ1UL602083
        Firmware Revision:  ZZ100-14
Standards:
        Used: ATA/ATAPI-7 T13 1532D revision 4a
        Supported: 7 6 5 4 & some of 8
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  268435455
        LBA48  user addressable sectors:  781422768
        device size with M = 1024*1024:      381554 MBytes
        device size with M = 1000*1000:      400088 MBytes (400 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        Queue depth: 32
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 1
        Recommended acoustic management value: 254, current value: 0
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 udma7
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    SMART feature set
                Security Mode feature set
           *    Power Management feature set
           *    Write cache
           *    Look-ahead
           *    Host Protected Area feature set
           *    WRITE_BUFFER command
           *    READ_BUFFER command
           *    NOP cmd
           *    DOWNLOAD_MICROCODE
                SET_MAX security extension
                Automatic Acoustic Management feature set
           *    48-bit Address feature set
           *    Device Configuration Overlay feature set
           *    Mandatory FLUSH_CACHE
           *    FLUSH_CACHE_EXT
           *    SMART error logging
           *    SMART self-test
           *    General Purpose Logging feature set
           *    SATA-I signaling speed (1.5Gb/s)
           *    SATA-II signaling speed (3.0Gb/s)
           *    Native Command Queueing (NCQ)
           *    Host-initiated interface power management
           *    Phy event counters
                DMA Setup Auto-Activate optimization
                Device-initiated interface power management
           *    Software settings preservation
           *    SMART Command Transport (SCT) feature set
           *    SCT Long Sector Access (AC1)
           *    SCT LBA Segment Access (AC2)
           *    SCT Error Recovery Control (AC3)
           *    SCT Features Control (AC4)
           *    SCT Data Tables (AC5)
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
                supported: enhanced erase
        228min for SECURITY ERASE UNIT. 228min for ENHANCED SECURITY ERASE UNIT.
Checksum: correct

mfg
Twilo

thorben · Beitrag von **thorben** » 21.03.2008 15:21:13

platte hin? controller hin? kabel hin? irgendsowas würd ich tippen, steht ja eh da...

gruß
thorben

Twilo · Beitrag von **Twilo** » 21.03.2008 15:28:17

Hi

thorben hat geschrieben:platte hin? ]controller hin?

gute Frage

thorben hat geschrieben:kabel hin?

werde ich mal gleich wechseln

thorben hat geschrieben:irgendsowas würd ich tippen, steht ja eh da...

wie meinst du das mit steht ja eh da?

ich hab das Gefühl, dass das Problem nur auftritt, wenn ich etwas größeres herunterlade oder ein dist-upgrade durchführe

mfg
twilo

Danielx · Beitrag von **Danielx** » 21.03.2008 16:43:09

Es könnte am Kernel 2.6.22 liegen, siehe hier:
https://www.debianforum.de/forum/viewtopic.php?t=91227

Gruß,
Daniel

uwepr · Beitrag von **uwepr** » 21.03.2008 18:47:15

Hallo Twilo,
vielleicht die Platte mit den

smartmontools

überprüfen. Infos gibt's hier:
http://wiki.ubuntuusers.de/Festplattenstatus
http://de.wikipedia.org/wiki/Self-Monit ... Technology
Viele Grüße! Uwe Pr.

Twilo · Beitrag von **Twilo** » 22.03.2008 13:23:39

Hi

bei der Festplatte habe ich einen kurzen Check mit den smartmontools durchlaufen lassen

Code: Alles auswählen

smartctl -l selftest /dev/sda
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      4583         -

nachdem ich auf Debian sid gegangen bin

Code: Alles auswählen

Linux kay-desktop 2.6.24-1-amd64 #1 SMP Mon Feb 11 13:47:43 UTC 2008 x86_64 GNU/Linux

erhalte ich jetzt folgende Meldung in der kern.log

Code: Alles auswählen

Mar 22 11:45:57 kay-desktop kernel: Driver 'sd' needs updating - please use bus_type methods
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] Write Protect is off
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] Write Protect is off
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 22 11:45:57 kay-desktop kernel:  sda: sda1 sda2
Mar 22 11:45:57 kay-desktop kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] Write Protect is off
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] Write Protect is off
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 22 11:45:57 kay-desktop kernel:  sdb: sdb1
Mar 22 11:45:57 kay-desktop kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Mar 22 11:45:57 kay-desktop kernel: hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2

komplette Ausgabe von heute http://nopaste.debianforum.de/7699

laut den Beitrag soll die meldung "Driver 'sd' needs updating - please use bus_type methods" harmlos sein - ob das jedoch stimmt kann ich leider nicht beurteilen

mfg
Twilo

uwepr · Beitrag von **uwepr** » 22.03.2008 14:17:40

Hallo Twilo,
'ne googelei nach "SATA link down (SStatus 0 SControl 300)" ergab u.a.:
http://kanotix.com/PNphpBB2-viewtopic-t-23862.html
Vielleicht doch das Kabel, ansonsten mehrere offene threads...z.B.:
http://www.meinews.net/festplatte-t1246 ... 080e9a08e2&
Viele Grüße! Uwe Pr.