KBDCALLS hat geschrieben:Na klar mußt d di isapnptools von Sarge installieren. Ließen sich sogar auf Lenny installieren. Hat zwar nix ausgespuckt. Was bei mir logisch ist habe keine ISAkarten noch Slots.
Ich weiß, ISA-Karten sind nicht mehr ganz State-Of-The-Art
Also isapnp wirf mir folgendes aus:
Code: Alles auswählen
# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
# Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#
# Trying port address 0273
# Board 1 has serial identifier 6e ff ff ff ff 12 11 b2 50
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 6e ff ff ff ff 12 11 b2 50)
# Vendor Id TER1112, No Serial Number (-1), checksum 0x6E.
# Version 1.0, Vendor version 1.0
# ANSI string -->AudioSystem EWS64 S<--
#
# Logical device id TER1100
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1112/-1 (LD 0
# ANSI string -->CoDec<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 1))
# Next DMA channel 0.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0530))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x05f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0100))
# Start dependent functions: priority functional
# IRQ 5, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x05f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0100))
# End dependent functions
(NAME "TER1112/-1[0]{CoDec }")
# (ACT Y)
))
#
# Logical device id TER1101
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1112/-1 (LD 1
# ANSI string -->MIDI-2<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0360
# Maximum IO base address 0x0360
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0360))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0100))
# End dependent functions
(NAME "TER1112/-1[1]{MIDI-2 }")
# (ACT Y)
))
#
# Logical device id TER1102
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1112/-1 (LD 2
# ANSI string -->Game Port<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200))
# End dependent functions
(NAME "TER1112/-1[2]{Game Port }")
# (ACT Y)
))
#
# Logical device id TER1103
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1112/-1 (LD 3
# ANSI string -->Digital CTRL<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0328
# Maximum IO base address 0x0328
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0328))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x032a
# Maximum IO base address 0x032a
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x032a))
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0100))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0100))
# End dependent functions
(NAME "TER1112/-1[3]{Digital CTRL }")
# (ACT Y)
))
#
# Logical device id TER1104
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1112/-1 (LD 4
# ANSI string -->Synth<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 9 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0330))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100))
# End dependent functions
(NAME "TER1112/-1[4]{Synth }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
Kannst du damit was anfangen?
Grüße
