Probleme mit eth0

[Deustferhan]

Hallo ich bin ein Linuxeinsteiger und habe probleme mit meinem netzwerk ich habe es mehrmals versucht wieder hochzubekommen aber irgendwie funzt es net er macht immer diese fehlermeldung!!
Habe es einfach kopiert aus der Konsole.

Password:
debian:/home/debian# /etc/init.d/networking
Usage: /etc/init.d/networking {start|stop|restart|force-reload}
debian:/home/debian# /etc/init.d/networking force-reload
* /etc/network/options is deprecated (see README.Debian of netbase).
Setting up IP spoofing protection...done (rp_filter).
Reconfiguring network interfaces...Internet Software Consortium DHCP Client 2.0pl5
Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
All rights reserved.

Please contribute if you find this software useful.
For info, please visit http://www.isc.org/dhcp-contrib.html

Listening on LPF/eth0/00:0b:6a:99:85:58
Sending on LPF/eth0/00:0b:6a:99:85:58
Sending on Socket/fallback/fallback-net
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
receive_packet failed on eth0: Network is down
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
No DHCPOFFERS received.
No working leases in persistent database.

Exiting.

Failed to bring up eth0.
done.
debian:/home/debian# ifconfig eth0 up
debian:/home/debian# ifconfig eth0 down
debian:/home/debian# ifconfig eth0 up
debian:/home/debian# dhclient eth0
Internet Software Consortium DHCP Client 2.0pl5
Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
All rights reserved.

Please contribute if you find this software useful.
For info, please visit http://www.isc.org/dhcp-contrib.html

Listening on LPF/eth0/00:0b:6a:99:85:58
Sending on LPF/eth0/00:0b:6a:99:85:58
Sending on Socket/fallback/fallback-net
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 20
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
No DHCPOFFERS received.
No working leases in persistent database.

Sleeping.

debian:/home/debian# /etc/init.d/networking start
* /etc/network/options is deprecated (see README.Debian of netbase).
Setting up IP spoofing protection...done (rp_filter).
Configuring network interfaces...Internet Software Consortium DHCP Client 2.0pl5
Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
All rights reserved.

Please contribute if you find this software useful.
For info, please visit http://www.isc.org/dhcp-contrib.html

Listening on LPF/eth0/00:0b:6a:99:85:58
Sending on LPF/eth0/00:0b:6a:99:85:58
Sending on Socket/fallback/fallback-net
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
receive_packet failed on eth0: Network is down
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
No DHCPOFFERS received.
No working leases in persistent database.

Exiting.

Es wäre gut wenn mir jemand hefen könnte
Lg Ferhan


[/code]

[altzheimer]

Moin!

receive_packet failed on eth0: Network is down

Kannst du einen Hardwarefehler ausschließen?

Gruß
Stephan

[Deustferhan]

Ja weil unter win Funzt die scjeiße ja....

[Deustferhan]

debian:/home/debian# dmesg
Linux version 2.6.20.1 (root@debian) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #3 PREEMPT Fri Mar 16 19:57:54 CET 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end: 000000003fff0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000003fff0000 size: 0000000000008000 end: 000000003fff8000 type: 3
copy_e820_map() start: 000000003fff8000 size: 0000000000008000 end: 0000000040000000 type: 4
copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 262128) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262128
early_node_map[1] active PFN ranges
0: 0 -> 262128
On node 0 totalpages: 262128
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 255 pages used for memmap
HighMem zone: 32497 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000fa8c0
ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x3fff0000
ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x3fff0030
ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x3fff00c0
ACPI: DSDT (v001 VIA K7VT4 0x00001000 INTL 0x02002024) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 2198.086 MHz processor.
Built 1 zonelists. Total pages: 260081
Kernel command line: root=/dev/hda3 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1033892k/1048512k available (1608k kernel code, 13900k reserved, 614k data, 192k init, 131008k highmem)
virtual kernel memory layout:
fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc032e000 - 0xc035e000 ( 192 kB)
.data : 0xc02920f5 - 0xc032baf4 ( 614 kB)
.text : 0xc0100000 - 0xc02920f5 (1608 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4398.71 BogoMIPS (lpj=2199357)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon(tm) XP 3200+ stepping 00
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfda71, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: dfe00000-dfefffff
PREFETCH window: bfd00000-dfcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2223k freed
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1175552790.633:1): initialized
highmem bounce pool size: 64 pages
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Bypassing VIA 8237 APIC De-Assert Message
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
Advanced Linux Sound Architecture Driver Version 1.0.14rc1 (Tue Jan 09 09:56:17 2007 UTC).
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:11.5 to 64
ALSA device list:
#0: VIA 8237 with CMI9761A+ at 0xc400, irq 16
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
S0 S1 S4 S5)
Freeing unused kernel memory: 192k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 17
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
hda: WDC WD1600BB-56GUA2, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: DVDRW IDE 16X, ATAPI CD/DVD-ROM drive
hdd: TOSHIBA DVD-ROM SD-M1912, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 18, io base 0x0000c800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: max request size: 512KiB
hda: Host Protected Area detected.
current capacity is 312579695 sectors (160040 MB)
native capacity is 312581808 sectors (160041 MB)
hda: Host Protected Area disabled.
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 > hda3
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 18, io base 0x0000cc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2 -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 18, io base 0x0000d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3 -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 18, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 18
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 18, io mem 0xdfffbe00
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 19
eth0: VIA Rhine II at 0x1c000, 00:0b:6a:99:85:58, IRQ 19.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 2-2: new full speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
EXT3 FS on hda3, internal journal
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
TCP highspeed registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retrieved PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=240.00 Mhz, System=200.00 MHz
radeonfb: PLL min 20000 max 40000
i2c_adapter i2c-2: unable to read EDID block.
i2c_adapter i2c-2: unable to read EDID block.
i2c_adapter i2c-2: unable to read EDID block.
i2c_adapter i2c-4: unable to read EDID block.
i2c_adapter i2c-4: unable to read EDID block.
i2c_adapter i2c-4: unable to read EDID block.
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb (0000:01:00.0): ATI Radeon Y`
pktgen v2.68: Packet Generator for packet performance testing.
NTFS driver 2.1.28 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device hda1): load_system_files(): Unsupported volume flags 0x4000 encountered.
NTFS-fs error (device hda1): load_system_files(): Volume has unsupported flags set. Mounting read-only. Run chkdsk and mount in Windows.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda2.
NTFS volume version 3.1.
NTFS volume version 3.1.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.25.0 20060524 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
debian:/home/debian# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
auto eth0
iface eth0 inet dhcp
debian:/home/debian# cat /var/log/faillog
pts/0(êíEtty½Ftty6l·ùEtty2ímóEdebian:/home/debian# cat /var/log/faillog
debian:/home/debian# ifconfig -a
eth0 Protokoll:Ethernet Hardware Adresse 00:0B:6A:99:85:58
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 b) TX bytes:1026 (1.0 KiB)
Interrupt:19 Basisadresse:0xc000

lo Protokoll:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)

debian:/home/debian# route -L
route: Ungültige Option -- L
Benutzung: route [-nNvee] [-FC] [<AF>] Kernelroutentabelle anzeigen
route [-v] [-FC] {add|del|flush} ... Routentabelle für AF ändern.

route {-h|--help} [<AF>] Genaue Syntax für AF anzeigen.
route {-V|--version} Version/Autor anzeigen und Ende.

-v, --verbose Ausführliche Ausgaben
-n, --numeric don't resolve names
-e, --extend display other/more information
-F, --fib display Forwarding Information Base (default)
-C, --cache Routencache statt FIB anzeigen

<AF>=Use '-A <af>' or '--<af>'; default: inet
Liste möglicher Adressfamilien, die Routen unterstützen:
inet (DARPA Internet) inet6 (IPv6) ax25 (AMPR AX.25)
netrom (AMPR NET/ROM) ipx (Novell IPX) ddp (Appletalk DDP)
x25 (CCITT X.25)

[a-tobias]

moin. ist das richtig das du die ip per dhcp bekommen willst ?
Oder möchtest du ne statische IP.

auf den ersten blick siehts nämlich so aus, als wenn der keinen dhcp findet.

also wenns denn ne statische sein soll, dann mach das hier ma :

Code: Alles auswählen

/etc/networking/interfaces

iface eth0 inet static
        address 192.168.x.x
        netmask 255.255.255.0
        network 192.168.x.0
        broadcast 192.168.x.255
       gateway 192.168.x.x

danach /etc/init.d/networking restart

[Deustferhan]

der sagt die die datei oder das verzeichnis existiert nicht wenn ich

Code: Alles auswählen

/etc/networking/interfaces 

eingebe.................

[rolo]

der sagt die die datei oder das verzeichnis existiert nicht ...

die datei heisst

Code: Alles auswählen

/etc/network/interfaces

[a-tobias]

oh sorry. Da hab ich mich vertan mit dem verzeichniss.

[Deustferhan]

Ja danke ist ja kein problem habs geändert funzt leider trotzdem nicht .......
Ich würde euch gerne mehr infos geben ch weiß ja net wie......
Gruß Ferhan

[Pawel]

Könnte es sein, dass du einen neuen (selbstkompilierten) Kernel hast, der nicht aus dem Debian Repository stammt?
Könnte es zusätzlich sein, dass es mit dem von Debian mitgelieferten Kernel funktioniert hat und mit dem neuen nicht?

Wenn bei beiden Fragen die Antwort "ja" lautet, dann wissen wir schon mal weiter.

[benebeck]

@Deustferhan:

Du solltest uns auf jeden Fall sagen:

a) Welcher Kernel

Code: Alles auswählen

uname -r

b) wie sieht die /etc/network/interfaces aus?

c) wie bekommst Du Deine IP-Addresse? Statisch oder per DHCP? Das müsste sich auch unter Win herausfinden lassen.

mfg benebeck

[roli]

Hi,

Ich würde euch gerne mehr infos geben ch weiß ja net wie......

Nach Moeglichkeit nicht indem du die Sachen direkt hier reinschreibst, sondern in dem du NoPaste nutzt. Wenn du einen neuen Beitrag/Antwort schreibst, siehst du im oberen drittel eine Box "wichtiger Hinweis", dadrinnen steht

- Lange Codezeilen/Logs gehören nach NoPaste, in Deinen Beitrag dann der passende Link dazu.

So wie's hier bisher steht, macht mir das Lesen keinen Spass.

[Deustferhan]

Ich habe es erledigt er hat sich die IP per dhcp geholt und ich hatte es im rooter deaktiviert....
Danke jungs für eure hilfe