update-grub, danach geht nix mehr @ Strato

[roughelement]

Hi All,

ich hab bei Strato den Dedicated Server und hab docht ein einfaches

apt-get dist-upgrade zu etch gemacht.

danach direkt ein update-grub und nachm reboot fährt der server nicht mehr hoch. selbst per serConsole passiert nix mehr. Ich seh das rebootet wird aber danach ist nix mehr. Also keine Kernel Panics oder der gleichen. Hat wer eine Ahnung woran es liegen kann?

Und updatet update-grub nur die menu.list?

Danke für die infos im vorraus.

p.s. geraed gesehen, das ein software raid eingerichtet ist.

/dev/md1 78058520 722620 73370664 1% /
devshm 257856 4 257852 1% /dev/shm
/dev/md0 54348 18580 32962 37% /boot

[garibaldi]

Hi und Willkommen im Forum!

Falls du gar keine shell mehr starten kannst, wenn ich dich richtig verstanden habe, lässt sich wohl nichts mehr machen außer einer kompletten Neuinstallation.

Falls du doch nach dem booten zB. über <STRG><ALT><F2> in eine shell kommst, mal sehen was

Code: Alles auswählen

dmesg

sagt. Zudem im Verzeichnis /var/log/ auf Fehlersuche gehen, vor allem in den Dateien syslog und messages.

Gruß, garibaldi

[roughelement]

Hallo,

also da ging dann leider garnichts mehr, ich hab neu installiert (ist im mom kein Problem, da noch sonst nix auf dem Server ist). Hier also dann die Daten die du angefordert hast (ist ja verdammt lang):

Linux version 2.6.8-3-686 (root@lart) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Sat Jul 15 10:32:25 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fee0000 (usable)
BIOS-e820: 000000001fee0000 - 000000001fee3000 (ACPI NVS)
BIOS-e820: 000000001fee3000 - 000000001fef0000 (ACPI data)
BIOS-e820: 000000001fef0000 - 000000001ff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
found SMP MP-table at 000f38e0
On node 0 totalpages: 130784
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126688 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f7a70
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fee3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fee30c0
ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x1fee9540
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x1fee9680
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fee9780
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fee9480
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,57600
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 2009.688 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510508k/523136k available (1552k kernel code, 11880k reserved, 689k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3981.31 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=0 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2008.0953 MHz.
..... host bus clock speed is 200.0895 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4700k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 3.00 entry at 0xfa790, last bus=5
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs *3 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LFID] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fb300
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb330, dseg 0xf0000
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 23 (level, low) -> IRQ 177
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, low) -> IRQ 185
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:02.1 -> GSI 21 (level, low) -> IRQ 193
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 19 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 201
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 02000000
....... : arbitration: 02
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 0 0 0 0 0 1 1 31
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 41
03 001 01 0 0 0 0 0 1 1 49
04 001 01 0 0 0 0 0 1 1 51
05 001 01 0 0 0 0 0 1 1 59
06 001 01 0 0 0 0 0 1 1 61
07 001 01 1 0 0 0 0 1 1 69
08 001 01 0 0 0 0 0 1 1 71
09 001 01 0 1 0 0 0 1 1 79
0a 001 01 0 0 0 0 0 1 1 81
0b 001 01 0 0 0 0 0 1 1 89
0c 001 01 0 0 0 0 0 1 1 91
0d 001 01 0 0 0 0 0 1 1 99
0e 001 01 0 0 0 0 0 1 1 A1
0f 001 01 0 0 0 0 0 1 1 A9
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 001 01 1 1 0 1 0 1 1 C9
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 C1
16 001 01 1 1 0 1 0 1 1 B9
17 001 01 1 1 0 1 0 1 1 B1
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ2 -> 0:2
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ201 -> 0:19
IRQ193 -> 0:21
IRQ185 -> 0:22
IRQ177 -> 0:23
.................................... done.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4700 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
tg3.c:v3.10 (September 14, 2004)
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:04:00.0 to 64
tg3: tg3_request_firmware (eth%d): Couldn't get firmware "tg3/tso-1.4.0".
tg3: eth%d: Firmware "tg3/tso-1.4.0" not loaded; continuing without TSO.
eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:e0:81:58:53:0a
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0]
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
3ware Storage Controller device driver for Linux v1.26.00.039.
3w-xxxx: No cards found.
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xe800-0xe807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe808-0xe80f, BIOS settings: hdc:DMA, hdd:DMA
hda: ExcelStor Technology J880, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(133)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
hdc: ExcelStor Technology J880, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 1024KiB
hdc: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(133)
/dev/ide/host0/bus1/target0/lun0: p1 p2 p3
libata version 1.02 loaded.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: raid1 personality registered as nr 3
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
md: md0 stopped.
md: bind<hdc1>
md: bind<hda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<hdc3>
md: bind<hda3>
md: md1: raid array is not clean -- starting background reconstruction
raid1: raid set md1 active with 2 out of 2 mirrors
md: syncing RAID array md1
md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc.
md: using maximum available idle IO bandwith (but not more than 200000 KB/sec) for reconstruction.
md: using 128k window, over a total of 79304768 blocks.
cramfs: wrong magic
EXT2-fs warning (device md1): ext2_fill_super: mounting ext3 filesystem as ext2

Adding 1052248k swap on /dev/hda2. Priority:-1 extents:1
Adding 1052248k swap on /dev/hdc2. Priority:-2 extents:1
Generic RTC Driver v1.07
Capability LSM initialized
NET: Registered protocol family 17
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0300140(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
md: md1: sync done.
RAID1 conf printout:
--- wd:2 rd:2
disk 0, wo:0, o:1, dev:hda3
disk 1, wo:0, o:1, dev:hdc3

Vielen Dank für dein Interesse am Problem.

[roughelement]

So,

hab weiterhin Sachen getestet und es nun hinbekommen.
update-grub hat mir den Consolen Zugriff aus dem menu.list überschrieben.

Jedoch kann ich immer noch nicht mit dem Kernel aus der etch Booten. Folgender Fehler passiert dann :

root (hd0,0)
Filesystem type is ext2fs, partition type 0xfd
kernel /vmlinuz-2.6.17-2-686 root=/dev/md1 ro console=tty0 console=ttyS0,57600
[Linux-bzImage, setup=0x1e00, size=0x12668e]
initrd /initrd.img-2.6.17-2-686
[Linux-initrd @ 0x1fa67000, 0x468fb1 bytes]
savedefault
boot
Linux version 2.6.17-2-686 (Debian 2.6.17-9) (waldi@debian.org) (gcc version 4.1.2 20060901 ( prerelease) (Debian 4.1.1-13)) #1 SMP Wed Sep 13 16:34:10 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fee0000 (usable)
BIOS-e820: 000000001fee0000 - 000000001fee3000 (ACPI NVS)
BIOS-e820: 000000001fee3000 - 000000001fef0000 (ACPI data)
BIOS-e820: 000000001fef0000 - 000000001ff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
found SMP MP-table at 000f38e0
DMI 2.2 present.
ACPI: PM-Timer IO Port: 0x1008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1ff00000:c0100000)
Built 1 zonelists
Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,57600
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2009.469 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510996k/523136k available (1482k kernel code, 11592k reserved, 544k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4023.08 BogoMIPS (lpj=8046164)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 02
Total of 1 processors activated (4023.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4515k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
PCI: No mmconfig possible on 0:18
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs *3 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LFID] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x1000-0x107f could not be reserved
pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
pnp: 00:01: ioport range 0x1400-0x147f has been reserved
pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:01: ioport range 0x1800-0x187f has been reserved
pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
PCI: Bridge: 0000:00:09.0
IO window: d000-dfff
MEM window: fc000000-fdffffff
PREFETCH window: fea00000-feafffff
PCI: Bridge: 0000:00:0b.0
IO window: c000-cfff
MEM window: fe900000-fe9fffff
PREFETCH window: fe800000-fe8fffff
PCI: Bridge: 0000:00:0c.0
IO window: b000-bfff
MEM window: fe700000-fe7fffff
PREFETCH window: fe600000-fe6fffff
PCI: Bridge: 0000:00:0d.0
IO window: a000-afff
MEM window: fe500000-fe5fffff
PREFETCH window: fe400000-fe4fffff
PCI: Bridge: 0000:00:0e.0
IO window: 9000-9fff
MEM window: fe300000-fe3fffff
PREFETCH window: fe200000-fe2fffff
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1164195256.972:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI wakeup devices:
HUB0 XVR0 XVR1 XVR2 XVR3 USB0 USB2 MMAC MMCI UAR1
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Loading, please wait...
Begin: Loading essential driverse100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
... ...
e100: Copyright(c) 1999-2005 Intel Corporation
tg3.c:v3.59.1 (August 25, 2006)
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 217
eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000BaseT Ethernet 00 :e0:81:58:53:0a
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
Intel(R) PRO/1000 Network Driver - version 7.0.33-k2-NAPI
Copyright (c) 1999-2005 Intel Corporation.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xe800-0xe807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe808-0xe80f, BIOS settings: hdc:DMA, hdd:DMA
hda: ExcelStor Technology J880, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: ExcelStor Technology J880, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
SCSI subsystem initialized
3ware Storage Controller device driver for Linux v1.26.02.001.
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
md: raid1 personality registered for level 1
Done.
Begin: Running /scripts/init-premount ...
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (55 C)
hda: max request size: 512KiB
hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(133)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
hda: cache flushes supported
hda:ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.1 -> Link [APCL] -> GSI 23 (level, low) -> IRQ 225
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: irq 225, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hda1 hda2 hda3
hdc: max request size: 512KiB
hdc: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(133)
hdc: cache flushes supported
hdc: hdc1 hdc2 hdc3
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 233
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 233, io mem 0xfebff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Begin: Loading MD modules ...
md: linear personality registered for level -1
Success: loaded module linear.
md: multipath personality registered for level -4
Success: loaded module multipathmd: raid0 personality registered for level 0
.
Success: loaded module raid0.
Success: loaded module raid1.
modprobe: FATAL:raid5: automatically using best checksumming function: pIII_sse
Module raid456 not found.

Failure: failed to load module raid456.
pIII_sse : 6378.000 MB/sec
raid5: using function: pIII_sse (6378.000 MB/sec)
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
Success: loaded module raid5.
raid6: int32x1 829 MB/s
raid6: int32x2 847 MB/s
raid6: int32x4 802 MB/s
raid6: int32x8 545 MB/s
raid6: mmxx1 1665 MB/s
raid6: mmxx2 2998 MB/s
raid6: sse1x1 1490 MB/s
raid6: sse1x2 2527 MB/s
raid6: sse2x1 2527 MB/s
raid6: sse2x2 3074 MB/s
raid6: using algorithm sse2x2 (3074 MB/s)
md: raid6 personality registered for level 6
Success: loaded module raid6.
md: raid10 personality registered for level 10
Success: loaded module raid10.
Done.
Warning: missing mdadm.conf file, trying to create one...
Success: mdadm.conf created.
Begin: Assembling all MD arrays ..md: md0 stopped.
.
md: bind<hdc1>
md: bind<hda1>
raid1: raid set md0 active with 2 out of 2 mirrors
mdadm: /dev/md0 md: md1 stopped.
has been started with 2 drives.
md: bind<hdc3>
md: bind<hda3>
raid1: raid set md1 active with 2 out of 2 mirrors
mdadm: /dev/md1 has been started with 2 drives.
Success: assembled all arrays.
Done.
Done.
Begin: Running /scripts/local-premount ...
kinit: name_to_dAttempting manual resume
ev_t(/dev/hdc2) = hdc2(22,2)
kinit: trying to resume from /dev/hdc2
kinit: No resume image, doing normal boot.kjournald starting. Commit interval 5 seconds
..
Done.
EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
INIT: version 2.86 booting
Setting hostname to '(none)'...hostname: the specified hostname is invalid
done.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40
input: PC Speaker as /class/input/input0
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.12ac
BUG: unable to handle kernel NULL pointer dereference at virtual address 0000000c
printing eip:
b0200282
*pde = 00000000
Oops: 0000 [#1]
SMP
Modules linked in: rtc psmouse serio_raw 8250_pnp evdev pcspkr i2c_nforce2 i2c_core ext3 jbd mbcache raid10 raid6 raid5 xor raid0 multipath linear ide_generic ohci_hcd ehci_hcd usbcore i de_disk thermal processor fan sata_nv raid1 md_mod sata_svw libata sd_mod generic 3w_xxxx scs i_mod piix amd74xx ide_core e1000 tg3 e100 mii
CPU: 0
EIP: 0060:[<b0200282>] Not tainted VLI
EFLAGS: 00010206 (2.6.17-2-686 #1)
EIP is at uart_write_room+0x9/0x16
eax: cf1d3800 ebx: 00000006 ecx: cf1e5540 edx: 00000000
esi: cf236000 edi: cf56ec00 ebp: 00000006 esp: cf27df18
ds: 007b es: 007b ss: 0068
Process S03udev (pid: 2197, threadinfo=cf27c000 task=cf1e5540)
Stack: b01f456d cf56ec00 cf321e40 00000282 00000000 cf1e5540 b0116f2d cf236138
cf236138 00000006 cf236000 00000006 00000006 b01f21d3 00000006 080f6408
cf321e40 b01f448c cf23600c cf2363e8 00000000 b01f2b64 cf321e40 cf321e40
Call Trace:
<b01f456d> write_chan+0xe1/0x293 <b0116f2d> default_wake_function+0x0/0xc
<b01f21d3> tty_write+0x147/0x1d8 <b01f448c> write_chan+0x0/0x293
<b01f2b64> redirected_tty_write+0x1c/0x6c <b01f2b48> redirected_tty_write+0x0/0x6c
<b0153379> vfs_write+0xa1/0x140 <b0153963> sys_write+0x3c/0x63
<b0102b4f> syscall_call+0x7/0xb
Code: 09 08 8b 40 10 74 09 81 60 10 ff ff ff fd eb 07 81 48 10 00 00 00 02 8b 5e 68 89 f0 ff 53 2c 5b 5e c3 8b 80 80 01 00 00 8b 50 10 <8b> 42 0c 2b 42 08 48 25 ff 0f 00 00 c3 8b 80 80 0 1 00 00 8b 50
EIP: [<b0200282>] uart_write_room+0x9/0x16 SS:ESP 0068:cf27df18

[nepos]

Kannst du diese ellenlangen Ausgaben bitte nach NoPaste packen?
Siehe auch Verhaltensregeln.
Danke dir!

Zu deinem 2. Log: da scheint was grueber faul zu sein. Der Kernel schmiert da mit einer Null Pointer Exception ab. Was da nun aber faul ist, keine Ahnung.

[roughelement]

Kannst du diese ellenlangen Ausgaben bitte nach NoPaste packen?
Siehe auch Verhaltensregeln.
Danke dir!

Zu deinem 2. Log: da scheint was grueber faul zu sein. Der Kernel schmiert da mit einer Null Pointer Exception ab. Was da nun aber faul ist, keine Ahnung.

Hi Nepos,

sorry das mit den nopaste wusst ich net. Werde es in Zukunft natürlich beherzigen.

Danke für den Hinweis.

[roughelement]

Hallo @ All,

ich hab heute dann nen 2.6.18er Kernel selbst Kompiliert und der Läuft ohne Probleme.
wieso der 17er nicht lief ist mir jetzt erstmal egal Habtsache es läuft.

Danke für eure Hilfe

[sannny]

http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=383264