Hi!
Wollte ma schaun, wie warm mein Rechner wird... (vorallem die CPU)
Ich hab allerdings keine ahnung, welche software es da gibt...
Gibts da der einfachheit halber auch irgendwas über apt-get?
Danke schonmal
ToMiNaToR
Temperatursoftware mit gui
Re: Temperatursoftware mit gui
Hallo
ich habe jetzt mall lm-sensors instaliert aber irgentwie stimmen die werte nichcpu 146 das kann nicht sein
in der
etc/modules steht das hier
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
# Parameters can be specified after the module name.
loop
# Generated by sensors-detect on Tue Feb 23 21:31:50 2010
# Chip drivers
via686a
und in der sensors3.conf steht unter via das hir
chip "via686a-*"
# VIA is very specific about the voltage sensor inputs, and our labels
# reflect what they say. Unfortunately, they are not at all specific about
# how to convert any of the register values to real units. Fortunately,
# Jonathan Yew and Alex van Kaam came through with some data for temp
# conversion and formulae for voltage conversion. However, the conversions
# should be regarded as our best guess - YMMV.
# On the Tyan S1598, the 2.5V sensor reads 0 and is not displayed in the BIOS.
# Linas Vepstas reports that this sensor shows nothing of
# interest on the Abit KA7 (Athlon), and is also not displayed in the BIOS.
# Likewise, Johannes Drechsel-Burkhard reports that this
# sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So,
# if you have one of these boards you may want to uncomment the 'ignore in1'
# line below.
label in0 "CPU core"
label in1 "+2.5V"
#ignore in1
label in2 "I/O"
label in3 "+5V"
label in4 "+12V"
#label fan1 "CPU Fan"
label fan2 "CPU Fan"
# VIA suggests that temp3 is an internal temp sensor for the 686a. However,
# on the Tyan S1598 as well as the Abit KA7 (Athalon), the absolute values
# of the readings from that sensor are not valid. The readings do seem to
# correlate with temp changes, but the conversion factor may be quite
# different from temp1 & temp2 (as noted above, VIA has not provided
# conversion info). So, you may wish to 'ignore temp3'.
# Johannes Drechsel-Burkhard notes that on his MSI K7T Pro,
# temp1 is the CPU temp and temp2 is the SYS temp. Hugo van der Merwe notes
# the same for his Gigabyte GA-7DXC, Olivier Martin for his Gigabyte
# GA-7ZM and Patrick Thomson for his Chaintech CT-5ATA.
# Thomas Anglmaier notes: on Epox EP-7kxa temp2 is CPU and temp1 is SYS.
label temp1 "SYS Temp"
label temp2 "CPU Temp"
label temp3 "SBr Temp"
#ignore temp3
# Set your CPU core limits here if the BIOS did not.
#set in0_min 1.70 * 0.95
#set in0_max 1.70 * 1.05
# Other voltage values are standard so we can enforce the limits.
# set in1_min 2.5 * 0.95
# set in1_max 2.5 * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5 * 0.9
# set in3_max 5 * 1.1
# set in4_min 12 * 0.9
# set in4_max 12 * 1.1
# Set your temp limits here. Remember, 'tempX_max' is the temp at which an
# alarm is triggered, and 'tempX_max_hyst' is the temp at which an alarm turns off.
# Setting tempX_max_hyst to a few degrees below the corresponding tempX_max
# prevents an oscillation between alarm on and off states. This kind of
# oscillation is known as hyteresis, thus the name. (You typically get the
# most serious and troublesome hysteresis when a sensor triggers something to
# reduce the temp, thus creating a negative feedback loop. Even without that,
# we would still get some oscillation when the temp hovers around the limit
# due to noise.)
# set temp1_max_hyst 40
# set temp1_max 45
# set temp2_max_hyst 55
# set temp2_max 60
# set temp3_max_hyst 60
# set temp3_max 65
# You could set your fan limits too, but the defaults should be fine.
#set fan1_min 5000
#set fan2_min 5000
woh muss ich was ferändern das die werte stimmen
kann mir da einer weiterhelfen
Bezeichnung Wert Grenzwert
CPU Temp 146°C 75°C
SBr Temp 25°C 46°C
SYS Temp 146°C 75°C
ST340810A 35°C 60°
MFG Keggy
ich habe jetzt mall lm-sensors instaliert aber irgentwie stimmen die werte nichcpu 146 das kann nicht sein
in der
etc/modules steht das hier
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
# Parameters can be specified after the module name.
loop
# Generated by sensors-detect on Tue Feb 23 21:31:50 2010
# Chip drivers
via686a
und in der sensors3.conf steht unter via das hir
chip "via686a-*"
# VIA is very specific about the voltage sensor inputs, and our labels
# reflect what they say. Unfortunately, they are not at all specific about
# how to convert any of the register values to real units. Fortunately,
# Jonathan Yew and Alex van Kaam came through with some data for temp
# conversion and formulae for voltage conversion. However, the conversions
# should be regarded as our best guess - YMMV.
# On the Tyan S1598, the 2.5V sensor reads 0 and is not displayed in the BIOS.
# Linas Vepstas reports that this sensor shows nothing of
# interest on the Abit KA7 (Athlon), and is also not displayed in the BIOS.
# Likewise, Johannes Drechsel-Burkhard reports that this
# sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So,
# if you have one of these boards you may want to uncomment the 'ignore in1'
# line below.
label in0 "CPU core"
label in1 "+2.5V"
#ignore in1
label in2 "I/O"
label in3 "+5V"
label in4 "+12V"
#label fan1 "CPU Fan"
label fan2 "CPU Fan"
# VIA suggests that temp3 is an internal temp sensor for the 686a. However,
# on the Tyan S1598 as well as the Abit KA7 (Athalon), the absolute values
# of the readings from that sensor are not valid. The readings do seem to
# correlate with temp changes, but the conversion factor may be quite
# different from temp1 & temp2 (as noted above, VIA has not provided
# conversion info). So, you may wish to 'ignore temp3'.
# Johannes Drechsel-Burkhard notes that on his MSI K7T Pro,
# temp1 is the CPU temp and temp2 is the SYS temp. Hugo van der Merwe notes
# the same for his Gigabyte GA-7DXC, Olivier Martin for his Gigabyte
# GA-7ZM and Patrick Thomson for his Chaintech CT-5ATA.
# Thomas Anglmaier notes: on Epox EP-7kxa temp2 is CPU and temp1 is SYS.
label temp1 "SYS Temp"
label temp2 "CPU Temp"
label temp3 "SBr Temp"
#ignore temp3
# Set your CPU core limits here if the BIOS did not.
#set in0_min 1.70 * 0.95
#set in0_max 1.70 * 1.05
# Other voltage values are standard so we can enforce the limits.
# set in1_min 2.5 * 0.95
# set in1_max 2.5 * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5 * 0.9
# set in3_max 5 * 1.1
# set in4_min 12 * 0.9
# set in4_max 12 * 1.1
# Set your temp limits here. Remember, 'tempX_max' is the temp at which an
# alarm is triggered, and 'tempX_max_hyst' is the temp at which an alarm turns off.
# Setting tempX_max_hyst to a few degrees below the corresponding tempX_max
# prevents an oscillation between alarm on and off states. This kind of
# oscillation is known as hyteresis, thus the name. (You typically get the
# most serious and troublesome hysteresis when a sensor triggers something to
# reduce the temp, thus creating a negative feedback loop. Even without that,
# we would still get some oscillation when the temp hovers around the limit
# due to noise.)
# set temp1_max_hyst 40
# set temp1_max 45
# set temp2_max_hyst 55
# set temp2_max 60
# set temp3_max_hyst 60
# set temp3_max 65
# You could set your fan limits too, but the defaults should be fine.
#set fan1_min 5000
#set fan2_min 5000
woh muss ich was ferändern das die werte stimmen
kann mir da einer weiterhelfen
Bezeichnung Wert Grenzwert
CPU Temp 146°C 75°C
SBr Temp 25°C 46°C
SYS Temp 146°C 75°C
ST340810A 35°C 60°
MFG Keggy