Ich hab bei mir mal ein Knoppix-Debian installiert und habe auf Kernel 2.6.11 geupdatet.
Im lilo funzt aber die einstellung nich richtig. wenn ich eingebe /boot/linux-2.6.11 und neustarte bekomme ich nur so etwas wie L 99999999999 ect. .
Ich habe zwar noch eine Bootdiskette aber ich benötge dringenst den neuen Kernel.
Danke im Vorraus
Lilo konfiguaration funzt nicht
Die Ausgabe aus /boot lautet:
boot.0200 initrd.gz sid.bmp
boot.0300 knoppix-old-mbr.1110642492 System.map
boot.0303 linux-2.6.11 System.map-2.4.22-xfs
config-2.4.22-xfs map vmlinuz
debianlilo.bmp sarge.bmp vmlinuz-2.4.22-xfs
und die von cat /etc/lilo.conf :
vga=791
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
# bios=0x81
#disk=/dev/sda
# bios=0x80
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda3
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
timeout=150
# prompt
# single-key
# delay=100
# timeout=100
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
append="hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce"
# Boot up Linux by default.
#
default=Linux
image=/boot/linux-2.6.11
label=Linux
initrd=/usr/src/linux-2.6.11/arch/i386/boot/bzImage
read-only
# restricted
# alias=1
image=/boot/linux-2.6.11
. label=Linux 2.6.11
. read-only
#. restricted
#. alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
other=/dev/hda1
label="Windows(hda1)"
other=/dev/hdb1
label="Windows(hdb1)"
other=/dev/hdb5
label="Windows(hdb5)"
Ich muss dazu sagen das die Lilo.conf nicht von mir eingestellt wurde da ich noch ein kleiner Noob bin (Und ich stehe dazu).
boot.0200 initrd.gz sid.bmp
boot.0300 knoppix-old-mbr.1110642492 System.map
boot.0303 linux-2.6.11 System.map-2.4.22-xfs
config-2.4.22-xfs map vmlinuz
debianlilo.bmp sarge.bmp vmlinuz-2.4.22-xfs
und die von cat /etc/lilo.conf :
vga=791
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
# bios=0x81
#disk=/dev/sda
# bios=0x80
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda3
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
timeout=150
# prompt
# single-key
# delay=100
# timeout=100
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
append="hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce"
# Boot up Linux by default.
#
default=Linux
image=/boot/linux-2.6.11
label=Linux
initrd=/usr/src/linux-2.6.11/arch/i386/boot/bzImage
read-only
# restricted
# alias=1
image=/boot/linux-2.6.11
. label=Linux 2.6.11
. read-only
#. restricted
#. alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
other=/dev/hda1
label="Windows(hda1)"
other=/dev/hdb1
label="Windows(hdb1)"
other=/dev/hdb5
label="Windows(hdb5)"
Ich muss dazu sagen das die Lilo.conf nicht von mir eingestellt wurde da ich noch ein kleiner Noob bin (Und ich stehe dazu).
Hi,
99 invalid second stage index sector (LILO)
Errors 99 and 9A usually mean the map file (-m or map=) is not readable,
likely because LILO was not re-run after some system change, or there
is a geometry mis-match between what LILO used (lilo -v3 to display) and
what is actually being used by the BIOS (one of the lilo diagnostic disks,
available in the source distribution, may be needed to diagnose this
problem).
Es scheint als ob Du /sbin/lilo nicht ausgeführt hättest.
Mach mal
Falls Du Windoof nur 1 mal drauf hast, und es ist auf /dev/hda1,
und /dev/hdb1 + /dev/hdb5 nur Daten Part. sind dann kannst du
die Einträge löschen :
MfG konqi76
99 invalid second stage index sector (LILO)
Errors 99 and 9A usually mean the map file (-m or map=) is not readable,
likely because LILO was not re-run after some system change, or there
is a geometry mis-match between what LILO used (lilo -v3 to display) and
what is actually being used by the BIOS (one of the lilo diagnostic disks,
available in the source distribution, may be needed to diagnose this
problem).
Es scheint als ob Du /sbin/lilo nicht ausgeführt hättest.
Mach mal
Code: Alles auswählen
# /sbin/liloändere mal in# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
append="hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi
hdg=scsi hdh=scsi apm=power-off nomce"
Code: Alles auswählen
append="apm=power-off nomce"und /dev/hdb1 + /dev/hdb5 nur Daten Part. sind dann kannst du
die Einträge löschen :
Bedenke, immer wenn Du in der /etc/lilo.conf was änderst, musst Du /sbin/lilo aufruffen.other=/dev/hdb1
label="Windows(hdb1)"
other=/dev/hdb5
label="Windows(hdb5)"
MfG konqi76