Debian startet nach Stromausfall nicht mehr

[KP97]

Aber ein smartphone hast du?!
Ich nehme in solche Situationen ein Video auf...

So so, ein Video, aber was machen solche Leute wie z.B. ich, die gar kein Smartphone nutzen wollen?
Ganz einfach, die benutzen wie eh und je die Tastenkombi Strg+s zum anhalten und Strg+q (oder t, bin nicht mehr ganz sicher) zum weiterlaufen der Konsolenausgabe...
aber zugegeben, ist nicht so schön bunt...;-)

Man kann im bevorzugten Terminal auch in die Einstellungen schauen, dort kann auch die Ausgabe beeinflusst werden.

[borsti1987]

So so, ein Video, aber was machen solche Leute wie z.B. ich, die gar kein Smartphone nutzen wollen?
Ganz einfach, die benutzen wie eh und je die Tastenkombi Strg+s zum anhalten und Strg+q (oder t, bin nicht mehr ganz sicher) zum weiterlaufen der Konsolenausgabe...
aber zugegeben, ist nicht so schön bunt...

Danke für den Tipp werde ich mal ausprobieren

Man kann im bevorzugten Terminal auch in die Einstellungen schauen, dort kann auch die Ausgabe beeinflusst werden.

Ich denke nur das wird im Rescue-Mode erstmal schwierig

[borsti1987]

Habe den Rechner jetzt mal ne weile laufen lassen und es kommt noch wieder neue Meldungen hinzu.

Hier jetzt auch für ata5:

[kalle123]

Aber ein smartphone hast du?!
Ich nehme in solche Situationen ein Video auf...

So so, ein Video, aber was machen solche Leute wie z.B. ich, die gar kein Smartphone nutzen wollen?
Ganz einfach, die benutzen wie eh und je die Tastenkombi Strg+s zum anhalten und Strg+q (oder t, bin nicht mehr ganz sicher) zum weiterlaufen der Konsolenausgabe...
aber zugegeben, ist nicht so schön bunt...

Hast ja recht, bei Linux geht das, aber ein solches Problemchen mit den herunter ratternden Meldungen soll es ja auch bei anderen Systemen gelegentlich mal geben ....

Und nebenbei, meine Reflexe waren nie so toll und mit den Jahren

KH

[heisenberg]

Sieht insgesamt so aus, als ob mit Deiner Platte/Deinen Platten(oder der Controller oder die Kabel(letzteres unwahrscheinlich)) irgend etwas nicht in Ordnung ist. Die würde ich auch mal genauer prüfen. (Smart, Lesetests). Ich hoffe, Deine Daten sind gesichert.

[borsti1987]

Ich habe jetzt mal für alle Platten einen Selbstes durchgeführt

Code: Alles auswählen

smartctl -t long /dev/sdX

Code: Alles auswählen

smartctl -a /dev/sdX

liefert folgende Ergebnisse:

für die System SSD /dev/sdc:

Code: Alles auswählen

smartctl 6.6 2017-11-05 r4594 [i686-linux-4.19.0-14-686-pae] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     CHN-HFmSATA01M-032
Serial Number:    32CF04220116
LU WWN Device Id: 0 000000 000000000
Firmware Version: 20150213
User Capacity:    31.675.383.808 bytes [31,6 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      1.8 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon May 16 19:26:14 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x02) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x71) SMART execute Offline immediate.
                                        No Auto Offline data collection support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0002) Does not save SMART data before
                                        entering power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (  10) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x0039) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x0000   100   100   050    Old_age   Offline      -       0
  5 Reallocated_Sector_Ct   0x0002   100   100   050    Old_age   Always       -       10
  9 Power_On_Hours          0x0000   100   100   050    Old_age   Offline      -       21656
 12 Power_Cycle_Count       0x0000   100   100   050    Old_age   Offline      -       78
160 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       22
161 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       60
162 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       1
163 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       26
164 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       33222126
165 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       32766
166 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       32766
167 Unknown_Attribute       0x0000   100   100   050    Old_age   Offline      -       32506
192 Power-Off_Retract_Count 0x0000   100   100   050    Old_age   Offline      -       67
194 Temperature_Celsius     0x0000   100   100   050    Old_age   Offline      -       34
195 Hardware_ECC_Recovered  0x0000   100   100   050    Old_age   Offline      -       24528428
196 Reallocated_Event_Count 0x0000   100   100   050    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0000   100   100   050    Old_age   Offline      -       0
241 Total_LBAs_Written      0x0000   100   100   050    Old_age   Offline      -       805604
242 Total_LBAs_Read         0x0000   100   100   050    Old_age   Offline      -       12620

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Für die erste RAID HDD /dev/sda:

Code: Alles auswählen

smartctl 6.6 2017-11-05 r4594 [i686-linux-4.19.0-14-686-pae] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD40EFRX-68WT0N0
Serial Number:    WD-WCC4E2XDVEN2
LU WWN Device Id: 5 0014ee 2b78d3047
Firmware Version: 82.00A82
User Capacity:    4.000.787.030.016 bytes [4,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Tue May 17 17:48:51 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (51420) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 514) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x703d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   196   172   021    Pre-fail  Always       -       7200
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       78
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   028   028   000    Old_age   Always       -       52659
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       77
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       60
193 Load_Cycle_Count        0x0032   187   187   000    Old_age   Always       -       41225
194 Temperature_Celsius     0x0022   105   098   000    Old_age   Always       -       47
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       3
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     52649         -
# 2  Conveyance offline  Completed without error       00%     52611         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Für die zweit RAID HDD /dev/sdb:

Code: Alles auswählen

smartctl 6.6 2017-11-05 r4594 [i686-linux-4.19.0-14-686-pae] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD40EFRX-68WT0N0
Serial Number:    WD-WCC4E6KXYEZS
LU WWN Device Id: 5 0014ee 20ce1b567
Firmware Version: 82.00A82
User Capacity:    4.000.787.030.016 bytes [4,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Tue May 17 17:50:12 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (52860) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 529) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x703d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   197   172   021    Pre-fail  Always       -       7141
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       78
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   028   028   000    Old_age   Always       -       52659
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       77
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       60
193 Load_Cycle_Count        0x0032   187   187   000    Old_age   Always       -       41529
194 Temperature_Celsius     0x0022   103   096   000    Old_age   Always       -       49
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     52648         -
# 2  Conveyance offline  Completed without error       00%     52611         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Für die dritte RAID HDD /dev/sdd:

Code: Alles auswählen

smartctl 6.6 2017-11-05 r4594 [i686-linux-4.19.0-14-686-pae] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD40EFRX-68WT0N0
Serial Number:    WD-WCC4E2EN3N37
LU WWN Device Id: 5 0014ee 262377929
Firmware Version: 82.00A82
User Capacity:    4.000.787.030.016 bytes [4,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Tue May 17 17:50:44 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (53460) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 534) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x703d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   199   177   021    Pre-fail  Always       -       7016
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       78
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   028   028   000    Old_age   Always       -       52659
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       77
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       60
193 Load_Cycle_Count        0x0032   186   186   000    Old_age   Always       -       42802
194 Temperature_Celsius     0x0022   102   095   000    Old_age   Always       -       50
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       1
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     52649         -
# 2  Conveyance offline  Interrupted (host reset)      50%     52611         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Für die vierte RAID HDD /dev/sde:

Code: Alles auswählen

smartctl 6.6 2017-11-05 r4594 [i686-linux-4.19.0-14-686-pae] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD40EFRX-68WT0N0
Serial Number:    WD-WCC4E2JEE6Y3
LU WWN Device Id: 5 0014ee 20ce449de
Firmware Version: 82.00A82
User Capacity:    4.000.787.030.016 bytes [4,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue May 17 17:51:47 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (51720) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 517) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x703d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   197   174   021    Pre-fail  Always       -       7133
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       78
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   028   028   000    Old_age   Always       -       52660
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       77
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       60
193 Load_Cycle_Count        0x0032   188   188   000    Old_age   Always       -       38208
194 Temperature_Celsius     0x0022   104   098   000    Old_age   Always       -       48
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     52649         -
# 2  Conveyance offline  Completed without error       00%     52611         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Da ich nicht so firm darin bin, all die Informationen zu deuten, meine Frage ob jemand gravierende Dinge erkennt.

[heisenberg]

Da ich nicht so firm darin bin, all die Informationen zu deuten, meine Frage ob jemand gravierende Dinge erkennt.

Das macht gar nichts.

Es gibt da einen umfangreichen Artikel im Wiki:

Wiki des Debianforums: Festplattendiagnostik und -überwachung

Auch im Ubuntu-Users-Wiki gibt's einen weiteren hilfreichen Artikel dazu:

Ubuntuusers-Wiki: Festplattenstatus

Hier auch nochmal irgend ein Blog-Post, der die einzelnen Werte detailliert erklärt:

blog.pregos.info/2014/09/23/uebersicht-wichtige-s-m-a-r-t-werte-und-ihre-bedeutung/ | SMART-Werte und Ihre Bedeutung Ist in obigem DF-Wiki-Artikel enthalten.

[borsti1987]

Da ich nicht so firm darin bin, all die Informationen zu deuten, meine Frage ob jemand gravierende Dinge erkennt.

Das macht gar nichts.

Es gibt da einen umfangreichen Artikel im Wiki:

Wiki des Debianforums: Festplattendiagnostik und -überwachung

Auch im Ubuntu-Users-Wiki gibt's einen weiteren hilfreichen Artikel dazu:

Ubuntuusers-Wiki: Festplattenstatus

Danke für die Links!
Wenn ich das alles Richtig interpretiere scheinen meine Platten keine probleme zu haben

[rhHeini]

Würd ich nicht so unterschreiben. 2 Deiner Raid-Platten haben UDMA_CRC_Error_Count ungleich Null, d.h. die haben Kommunikationsprobleme über die SATA-Schnittstelle. Da mal Kabel ziehen und neu stecken, und den Wert beobachten ob der steigt. Im Zweifelsfall je ein neues SATA-Kabel spendieren.

Und die haben > 52000h Laufzeit. Du solltest mit Ausfällen rechnen.

Rolf

[borsti1987]

Kann man eigentlich sagen, das ein Meldung ata5.00: ... gleich Datenträger /dev/sde ist oder wie finde ich heraus welcher Datenträger betroffen ist?

[rhHeini]

Da schaust Du am besten im syslog nach welche Platte an welchem Port hängt.

[borsti1987]

Hab da noch einen netten einzeiler gefuden

Code: Alles auswählen

ls -l /sys/block/sd* | sed -e 's@.*-> \.\..*/ata@/ata@' -e 's@/host@ @' -e 's@/target.*/@ @'

hat bei mir funktioniert

sieht dann bei mir so aus:

Code: Alles auswählen

/ata1 0 sda
/ata2 1 sdb
/ata3 2 sdc
/ata5 4 sdd
/ata6 5 sde

edit: wobei das für mich irgendwie komisch ausschaut.
ata1,2,4,5 wären dann onboard und ata3 ist dann die PCI-Express Karte mit 1 x mSATA und 1 x SATA.
Kann das denn sein?

[heisenberg]

ata1,2,4,5 wären dann onboard und ata3 ist dann die PCI-Express Karte mit 1 x mSATA und 1 x SATA.
Kann das denn sein?

Prüfe es doch selbst nach. @rhHeini hatte die Systemprotokolle erwähnt. Das sind z. B. im Verzeichnis /var/log die Dateien syslog und kern.log. Wenn Du mit grep nach den passenden Mustern suchst, findest Du aufschlussreiche Informationen.

Code: Alles auswählen

grep -E 'ata[0-9]' /var/log/{sys,kern.}log

[heisenberg]

Wenn ich das alles Richtig interpretiere scheinen meine Platten keine probleme zu haben

Ich habe es mir nicht detailliert angeschaut. Ich bin nicht Deiner Meinung. Die Platten sehen nicht mehr gut aus.

load_cycle_count von ~40.000 ist bei allen Platten recht hoch. Das ist problematisch. Kann sein dass die alle nicht mehr fit sind. Typische Ursache von erhöhtem load_cycle_count sind eingeschaltete Energiespareinstellungen. Das ist für einen Server nicht gut. Das solltest Du auf jeden Fall ausschalten. Die Schreib-/Leseköpfe wechseln sonst sehr häufig zwischen Park- und Aktivitätsmodus hin- und her.

Hier mal ein Beispiel von einem Serverplattensatz mit ähnlicher Betriebszeit bei mir:

Code: Alles auswählen

sda
  9 Power_On_Hours          0x0032   001   001   000    Old_age   Always       -       79328
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       4

sdb
  9 Power_On_Hours          0x0032   038   038   000    Old_age   Always       -       45861
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       5

sdc
  9 Power_On_Hours          0x0012   090   090   000    Old_age   Always       -       73563
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       674

sdd
  9 Power_On_Hours          0x0012   090   090   000    Old_age   Always       -       73564
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       694

sde
  9 Power_On_Hours          0x0012   090   090   000    Old_age   Always       -       73566
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       679

sdf
  9 Power_On_Hours          0x0012   090   090   000    Old_age   Always       -       73562
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       681

---

Reallocated_Sector_Ct von 10 könnte, muss aber nicht, auf baldigen Ausfall der entsprechenden Platte hindeuten. Kann auch einfach wegen des Stromausfalls verursacht worden sein.

Die Platten sind zwar lange in Betrieb gewesen, aber deswegen alleine würde ich die noch nicht unbedingt austauschen.

---

Ich würde auch mal ein badblocks(non-destructive read-write mode) test drüber laufen lassen. Ich gehe für meine Empfehlungen davon aus, dass Du ein Backup hast. (Wenn die Platten ohnehin bald am abkratzen sein sollten, dann kann das sein, dass der badblocks denen den Rest gibt.)