USB Stick: mounting Probleme

[_ash]

Debian Stable. Wenn ich einen USB-Stick verbinde, wird dieser nicht auto-gemountet, stattdessen sehe ich in dmesg diese Fehler:

Code: Alles auswählen

[ 7676.380057] usb 1-3: new high-speed USB device number 5 using xhci_hcd
[ 7676.529663] usb 1-3: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 7676.529667] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7676.529670] usb 1-3: Product: USB DISK
[ 7676.529673] usb 1-3: Manufacturer: SMI Corporation
[ 7676.530896] usb-storage 1-3:1.0: USB Mass Storage device detected
[ 7676.531319] scsi host6: usb-storage 1-3:1.0
[ 7677.922121] scsi 6:0:0:0: Direct-Access     SMI      USB DISK         1100 PQ: 0 ANSI: 0 CCS
[ 7677.922704] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 7677.923068] sd 6:0:0:0: [sdc] 15974400 512-byte logical blocks: (8.18 GB/7.62 GiB)
[ 7677.923562] sd 6:0:0:0: [sdc] Write Protect is off
[ 7677.923565] sd 6:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 7677.924101] sd 6:0:0:0: [sdc] No Caching mode page found
[ 7677.924109] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 7678.052325] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7678.728340] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7679.404341] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7680.080303] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7680.760347] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7681.436345] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7681.974829]  sdc: sdc1
[ 7682.100356] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7682.776377] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7683.452352] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7684.132387] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7684.808405] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7685.484300] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7686.148386] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7686.824406] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7687.500426] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7688.176418] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7688.860387] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7689.540404] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7690.078149] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 7690.296440] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7690.972411] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7691.648435] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7692.324386] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7693.004459] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7693.680377] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7694.340462] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7695.016447] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 7695.692475] usb 1-3: reset high-speed USB device number 5 using xhci_hcd

Das passiert nicht mit allen Sticks, ein Kingston zB funktioniert stressfrei.

Ein Hardwarefehler ist es wohl nicht, dergleiche Stick geht an einem anderen Rechner problemlos. Ideen?

[debianoli]

Ja. Deine Hardware mag den nicht.
Teste es mal an einem anderen USB-Port. Dazu einen neueren Kernel aus den Backports und evtl einen alten Kernel aus Stretch testen.

[_ash]

Neuerer Kernel ist schwierig, das hatte ich mal getestet, aber da gibt es Schwierigkeiten mit dem NVIdia-Treiber